# changelog

author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.04-2.1
changelog:
  -     *The following fix was incorporated in this version:**
      
        *  Fixed NVRAM CRC error
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v155369/D3000_P07231-002.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.04-3.1
changelog:
  -     *The following fix was incorporated in this version:**
      
        *  Fixed NVRAM CRC error
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v157942/P07231-003.html) for the complete listing of fixes,
      enhancements, known issues and work-arounds corresponding to this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.12
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Fixed TLB exception during upgrade from Rev build 1.11.000 to 0412.000
      
        * Fixed expander bootstrap task which failed with 0xB1 error code appearing in the console due to missing NVRAM tag - Product Name
      
        * Enabled-ClusterS2D command that does not complete with SATA drive in D3610
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v154196/D3000_P07231-004.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.04
changelog:
  -     *The following enhancement has been added in this version:**
      
        * Added support of Rhel 7.8 
      
        * Added support of Rhel 8.2 
      
        * Added support of SLES15 SP2


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.04
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
      
        * The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
      
        * Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
      
        * If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v177052/D3000_P07231-006.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.04-2.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
      
        * The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
      
        * Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
      
        * If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v191363/D3000_v5.04B.html) for the complete listing of fixes,
      enhancements, known issues and work-arounds corresponding to this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.04-3.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
      
        * The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
      
        * Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
      
        * If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v202692/20-D3000-Gen10RN504C_ED3.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.04-7.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
      
        * The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
      
        * Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
      
        * If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v234600/20-D3000-Gen10RN504G_ED7.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 6.00-1.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Code optimization to save memory repo.
      
        * TLB exception seen while doing esp reset when expander reset was in progress.
      
        * Added the psoc 8.93 binary in peripheral images, updated the reveille version numbers.
      
        * Added whole new Delta PS-pmbus code , Updated the ESP version number.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1808229885/v234599/20-D3000B-Gen10RN600A_ED2.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-4.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v172139/D6020_P07232-006.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-5.1
changelog:
  -     *The following enhancement has been added in this version:**
      
        * Added support of Rhel 8


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-5.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v177006/D6020_v274_RN.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-7.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v183133/D6020_P07232-008.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-9.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v191364/D6020_v2.74I.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-10.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v202690/20-D6020-Gen10RN274J_ED8.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-14.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v234598/20-D6020-Gen10RN274N_ED12.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0105
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * SAS drive LED behavior was corrected to align with the Smart Array specification, specifically: 
          * The Activity LED of a sanitize erase drive now turns ON when connected.
      
          * The Array present LED now turns ON for the SAS drive.
      
          * The Activity LED now blinks on all drives during a SAS drive rebuild.
      
        * The Serial Output Buffer (SOB) has a fixed sized for stored entries. Now, when the buffer is full, the oldest entries are cleared or committed to persistent storage (if available). For this reason, subsequent requests to read the SOB only retrieves new entries that have been logged since the last successful request to read the SOB.
      
        * The drive activity LED has been changed to a function as described in the installation and maintenance guide.
      
        * The reboot flag was changed to issue a hard reset, which enables the service delivery subsystem (ZPSDS) information be shared across (expanded across) the internal expanders to all devices attached.
      
        * The drive activity LED on the SAS disk drives was changed to support the ACTIVE_LOW signal state. The ACTIVE_LOW signal state is the default operation state for most drives.
      
        * The SCSI WRITE BUFFER MODE was changed from activate to soft reset. This change improves the host ability to detect and report whether the enclosure is going to perform a disruptive or non-disruptive activation after a firmware upgrade.
      
        * With I/O module firmware v0105 and PQI firmware 2.02 , the slot power cycle issue has been resolved by changing the power cycle SES request to return a failure when a partner slot is not connected.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p480571592/v172138/D8000_P20366-002.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0107
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * In STD INQUIRY RESPONSE, the ErrM bit was always being set. The ErrM bit indicates that the enclosure firmware detects a mismatch in any of its package versions and the firmware version of a FRU component. The issue was due to an incorrect version of PSU firmware being included and that has been fixed.
      
        * After installing the latest firmware on the enclosure I/O modules, the SES targets could not be discovered on the host. The virtual phy bit in SMP DISCOVER RESPONSE, which is used by the Microchip smartpqi HBA, was det for the virtual phy of the I/O module.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p480571592/v183134/D8000_P20366-004.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0111
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Incorrect programming of the PHY ERROR COUNTERS parameter caused the amber LED to be lit, resulting in a false warning. The counter condition was corrected and the amber LED now functions correctly.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p480571592/v191365/D8000_v0111.html) for the complete listing of fixes,
      enhancements, known issues and work-arounds corresponding to this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0118
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * User was not able to collect ddump logs.
      
        * Logical Fault LED remains ON even after clearing the fault using "reboot soft"
      
        * Vendor ID showed as "DEFAULT" for D8000 expander in SSACLI enclosure detail
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p480571592/v203448/20-D8000-Gen10RN0118_ED1.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0130
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
        * PSU version is showing as "No Ver" after inserted the New bel power PSU.
        * GEM_5_2 Coverity defect fix.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p480571592/v218471/20-D8000-Gen10RN0130_ED1.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0130-2.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
        * PSU version is showing as "No Ver" after inserted the New bel power PSU.
        * GEM_5_2 Coverity defect fix.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p480571592/v234513/20-D8000-Gen10RN0130B_ED3.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.0.5435-2.1
changelog:
  -      Initial release of Firmware for HPE Persistent Memory for Gen10 Servers.
        * This product contains mainly performance improvements.
        * This product now supports Red Hat Enterprise Linux 8 and SUSE Linux Enterprise Server 12.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.2.0.1553-2.1
changelog:
  -     This product corrects an issue that three different capacities of Intel Optane
      DC Persistent Memory are identifiable with three individual device GUID.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.03.035
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial version of the firmware.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.03.039
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version of the System ROM contains updates aligned with the Tatlow PLR2
      BKC WW50.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.03.200
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the MCTP PCIe devices could not be discovered after
      an SPS firmware update without an AC power cycle. This issue is not unique to
      HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.03.204
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This version is in compliance with Intel IPU.2022.3 guidance.
      
      The following vulnerabilities have been addressed in this SPS release:
      CVE-2022-29515. These issues are not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.03.309
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2023.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the Server Platform Services Firmware provides mitigations
      for security vulnerability documented as CVE-2022-36794. This issue is not
      unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.113
changelog:
  -     This image contains the latest Intel Server Platform Services (SPS) Firmware
      which contains mitigations for a variety of security vulnerabilities. The
      following vulnerabilities have been addressed in this SPS release:
      CVE-2020-0545 and CVE-2020-0586. These issues are not unique to HPE Servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.208
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2020.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the Server Platform Services Firmware provides mitigations
      for security vulnerability documented as CVE-2020-8755. This security
      vulnerability is documented in Intel Security Advisory INTEL-SA-00391. This
      issue is not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.303
changelog:
  -     See the release document in Download Product Binaries page from Product
      Summary of the firmware product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.303
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2021.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the Server Platform Services (SPS) Firmware provides
      mitigations for SPS security vulnerabilities documented as CVE-2020-24509.
      These security vulnerabilities are documented in Intel Security Advisory
      INTEL-SA-00459.  These issues are not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.400
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2021.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the Server Platform Services (SPS) Firmware provides
      mitigations for SPS security vulnerabilities documented as CVE-2021-0060. This
      issue is not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.500
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2022.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with IPU.2022.1 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.600
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with IPU.2022.2 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.700
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2022.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with IPU.2022.3 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 05.01.04.804
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2023.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with IPU.2023.1 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2021.02.03
changelog:
  -     This is a fibre channel component.
      
      Added support for the following:
      
        * Code update to support new flash vendors
      
      Contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.352.24
      
      12.8.352.24
      
      12.8.352.10
      
      12.8.352.5
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.352.24
      
      12.8.352.24
      
      12.8.352.10
      
      12.8.352.5


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2021.10.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      12.8.528.12
      
      12.8.528.12
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      12.8.528.12
      
      12.8.528.12
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.12
      
      12.8.528.12
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.12
      
      12.8.528.12
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.12
      
      12.8.528.12
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.12
      
      12.8.528.12
      
      12.8.528.10
      
      12.8.502.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2021.11.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.03.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      12.8.528.21
      
      12.8.528.21
      
      12.8.528.10
      
      12.8.502.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.08.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.20
      
      14.0.499.20
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.20
      
      14.0.499.20
      
      14.0.499.2
      
      14.0.490.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.08.01-2.9
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.21
      
      14.0.499.21
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.20
      
      14.0.499.20
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.20
      
      14.0.499.20
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.20
      
      14.0.499.20
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.20
      
      14.0.499.20
      
      14.0.499.2
      
      14.0.490.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.10.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.03.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter
      
      16Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2021.02.01
changelog:
  -     *Fixed the following:-**
      
        * Enhancements have been made to the firmware to prevent and better recover from any stoppage as described in Customer Advisory available at [https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=a00094722en_us](https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=a00094722en_us)
        * Fixed a behavior where the number of active Input/Output (IO) exchanges could be reduced under certain fabric conditions, resulting in reduced performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2021.10.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      1.75.07
      
      9.06.02
      
      7.04
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      1.75.07
      
      9.06.02
      
      7.04
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      1.75.07
      
      9.06.02
      
      7.04
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      1.75.07
      
      9.06.02
      
      7.04
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.05.03
      
      09.06.02
      
      7.11
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.05.03
      
      09.06.02
      
      7.11
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.08.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.06.27
      
      09.09.00
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.08.27
      
      09.09.00
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.09.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      1.77.12
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.06.27
      
      09.09.00
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.06.27
      
      09.09.00
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.10.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.01
      
      09.09.00
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.01
      
      09.09.00
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.03.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.04.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.04.02
changelog:
  -     This Firmware package contains following firmware versions:
      
      Adapter
      
      Speed
      
      MBI
      
      Firmware
      
      UEFI
      
      Boot Bios
      
      HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter
      
      16Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.00.01
      
      9.09.00
      
      7.19
      
      3.64
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.04.02
changelog:
  -     The Firmware fixes the following:
      
        * Unsuccessful read of the SFP Temperature which will trigger a Server Shutdown. 
        * Message related to a Mailbox 0x48 Firmware dump saved to buffer.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.09.01
changelog:
  -     Fixed the following behavior:
      
      Temperature Misreading: the adapter was reading incorrect reading of the
      temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small
      Form-factor Pluggable. The symptom would result in a temperature spike and
      potentially reset the system


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10-2.1
changelog:
  -     *Following issues have been fixed in firmware version 12.28.1002:**
      
        * An issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
        * Increased PHY power consumption limit to 1.5w.
        * An issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.
      
      **No fixes are included in firmware version 16.31.1200.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.11
changelog:
  -     *Firmware for the following devices are updated to 12.28.2006:**
      
      825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)  
      825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)  
      
      
      **New Feature and Changes in Version 12.28.2006:**
      
        * Increased the maximum XRQ number to 512.
      
      
      
      **Firmware for the following devices are updated to 16.31.1200:**
      
      879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)  
      872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)  
      
      
      **New features and changes included in version 16.31.1200:**
      
        * NIC scheduling feature support has been disabled for non-privileged functions.
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Asymmetrical MSIX Configuration: This feature allows the device to be configured with a different number of MSIX vectors per physical PCI functions.To use this feature, please follow these steps: 
          *   Clear NUM_PF_MSIX_VALID to disable global symmetrical MSIX configuration.
          *   Set PF_NUM_PF_MSIX_VALID to enable asymmetrical per Physical Function MSIX configuration.
          *   Configure PF_NUM_PF_MSIX per physical PCI function.
        * RDMA partitioning and RDMA counters in IB mode.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.
        * Enabled UID 0 to create resources with UMEM (User Memory).
        * Receiving and sending native IB packets from/to the software (including all headers) via raw IBL2 QPs.
        * RX RDMA NIC flow table on an IB port. Now the software can steer native IB packets to raw IB receive queues according to the DLID and  the DQPN.
        * Added a new NVconfig per Port for a specific Finisar module. This new NVconfig sets the port to work in AN mode and sets the module to No DME. This change does not affect the speed logic, only the FEC logic (FEC override). **Note:** If the port does not go up, switch to Force mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.11
changelog:
  -     *Following issues have been fixed in firmware version 12.28.2006:**
      
        * An issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
        * Increased PHY power consumption limit to 1.5w.
        * An issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.
      
      **The following issues have been fixed in version 16.31.1200:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * An assert that was caused when trying to open 1024 functions on the device and the maximum number of functions was 1023.
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to hang.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
      
      **Additional Fixes included in version 16.31.1200:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.12
changelog:
  -     *Firmware for the following devices has been updated to 12.28.2006:**
      
        * 825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
        * 825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)  
      
      
      **Firmware for the following devices has been updated to 16.32.1010:**
      
        * 879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
        * 872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)
      
      
      
      **New Features and changes included in version 12.28.2006:**
      
        * Increased the maximum XRQ number to 512.
      
      
      
      **New features and changes included in version 16.32.1010:**
      
        * Added support for blocking unwanted GMP classes by dedicated MADs.
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Added a Congestion Control Key to all Congestion Control MADs to authenticate that they are originated from a trusted source.
        * Added an SMP firewall to block the option of sending SMPs (MADS sent on QP0 from the Subnet Manager) from unauthorized hosts to prevent fake SMPs from being recognized as the SM.
        * Vendor Specific MADs Class 0x9 is no longer supported by the firmware. In case the firmware detects such MAD, the firmware will return a "NOT SUPPORTED" error to the user.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for dynamic timeout mechanism when in InfiniBand mode.
        * Added support for QSHR access register to enable Set and Query rate limit perhost per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Added support for asymmetrical VFs per PF. To enable it: PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a none zero value.
        * Added 2 new MAD access registers to enable mlxlink to read/write access registers by LID (to the whole subnet).
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Disabled VST on dual port adapter cards when one port is configured as ETH and the other as IB as VST is not available when the port is set as ETH.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.12
changelog:
  -     *Fixes in version 12.28.2006:**
      
        * Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
        * Increased PHY power consumption limit to 1.5w.
        * Fixed n issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.
      
      **The following issues have been fixed in version 16.32.1010**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.
        * The system got into an unresponsive state when a peer port went down while using an Optical module.
        * Invalid RNR timeout when trying to set it during the rts2rts_qp transition.
        * A fatal assert 0x81C5 occurred when calling get_vport_mad from the MAD APIs. The firmware was trying to compute the number of vPorts using a global function number. To avoid this issue, the API was updated to remove any assumption on the function number. Note: This issue is affects only IB devices.
        * During events, stress caused the firmware to reset the Arm host of the vPort without sending an event. Thus preventing the software from rearming the vPort as it did not receive any event, and the firmware did not send the event because the vPort had no Arm set.
        * The system could not create more than 128K QPs.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
        * PCIe lane margining capability issues.
        * An issue related to the sl2vl mad that caused a few msec hiccup in the transmission on an InfiniBand network when the SM sent the sl2vl mad to a node in the cluster.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.13
changelog:
  -     *Firmware for the following devices has been updated to 12.28.2006:**
      
        * 825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
        * 825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)  
      
      
      **Firmware for the following devices has been updated to 16.33.1048:**
      
        * 879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
        * 872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)
      
      
      
      **New Features and changes included in version 12.28.2006:**
      
        * Increased the maximum XRQ number to 512.
      
      
      
      **New features and changes included in version 16.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter.
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.13
changelog:
  -     *Fixes in version 12.28.2006:**
      
        * Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
        * Increased PHY power consumption limit to 1.5w.
        * Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.
      
      **The following issues have been fixed in version 16.33.1048**
      
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * The card occasionally masked some PCIe AER reporting.
        * Incorrect flow of credits blockage that prevented booting during DC cycle test.
        * An issue with BMC medium migration from SMBUS to PCIe, and increased FIFOs to pass large packets in case of the migration.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14
changelog:
  -     *Firmware for the following devices has been updated to 12.28.2006:**
      
        * 825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
        * 825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)  
      
      
      **Firmware for the following devices has been updated to 16.35.1012:**
      
        * 879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
        * 872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)
      
      
      
      **New Features and changes included in version 12.28.2006:**
      
        * Increased the maximum XRQ number to 512.
      
      
      
      **New features and changes included in version 16.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14
changelog:
  -     *Fixes in version 12.28.2006:**
      
        * Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
        * Increased PHY power consumption limit to 1.5w.
        * Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.
      
      **The following issues have been fixed in version 16.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * Bad configuration of number of VFs and SFs led to the consumption of too many functions and triggered a FW assert 0x888E. The reduction flows behavior was fixed to ensure the configuration does not exceed the total number of supported functions. 
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.15
changelog:
  -     *The following issues have been fixed in version 12.28.2006:**
      
        * Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
        * Increased PHY power consumption limit to 1.5w.
        * Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.
      
      **The following issues have been fixed in version 16.35.3006:**
      
        * Packet loss that occurred when restarting the transmit. 
        * An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
        * A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
        * Added a missing VLAN strip.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8-2.1
changelog:
  -     *Fixes in version 2.42.5000:**
      
        * PortRcvPkts counter was prevented from being cleared after resetting it.
        * The system Timed Out on the configuration cycle of the Virtual Functions (VFs) when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hangs and results in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA, the RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * link did not go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Network Controller Sideband Interface (NC-SI) did not work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes in version 2.42.5044:**
      
        * Fixed an issue that  prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode 
      
      **Fixes in version 2.42.5052:**
      
        * Fixed Uncorrectable Machine Check Exception issue. The internal resources for handling packets were not allowed to be flushed when the driver was brought down and occasionally caused Red Screen of Death (RSOD). The fix was applied to the ROM code only and has only external timing influences upon the driver's teardown.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
          764282-B21  
          764286-B21  
      
      **Firmware for the following devices are updated to 2.42.5052:**  
          764283-B21  
          764284-B21  
          764285-B21
      
      **New features in firmware version 2.42.5000:**
      
        * Added support for the following features. 
          * new TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * A mechanism to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
          * A new field is added to "set port" command which notifies the firmware what is the user_mtu size.
        * Improved the debug ability for command timeout cases


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Fixes in version 2.42.5000:**
      
        * PortRcvPkts counter was prevented from being cleared after resetting it.
        * The system Timed Out on the configuration cycle of the Virtual Functions (VFs) when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hangs and results in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA, the RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * link did not go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Network Controller Sideband Interface (NC-SI) did not work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes in version 2.42.5052:**
      
        * Fixed Uncorrectable Machine Check Exception issue. The internal resources for handling packets were not allowed to be flushed when the driver was brought down and occasionally caused Red Screen of Death (RSOD). The fix was applied to the ROM code only and has only external timing influences upon the driver's teardown.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
          764282-B21  
          764286-B21  
      
      **Firmware for the following devices are updated to 2.42.5056:**  
          764283-B21  
          764284-B21  
          764285-B21
      
      **New features in firmware version 2.42.5000:**
      
        * Added support for the following features. 
          * new TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * A mechanism to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
          * A new field is added to "set port" command which notifies the firmware what is the user_mtu size.
        * Improved the debug ability for command timeout cases.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *Fixes in version 2.42.5000:**
      
        * PortRcvPkts counter was prevented from being cleared after resetting it.
        * The system Timed Out on the configuration cycle of the Virtual Functions (VFs) when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hangs and results in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA, the RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * link did not go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Network Controller Sideband Interface (NC-SI) did not work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes in version 2.42.5056:**
      
        * Fixed an issue that resulted in reading from invalid I/O address on handover from UEFI boot to OS boot, when a port was configured as InfiniBand on a VPI adapter device.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.11
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
          764282-B21  
          764286-B21  
      
      **Firmware for the following devices are updated to 2.42.5056:**  
          764283-B21  
          764284-B21
      
      **Firmware for the following device is updated to 2.42.5700:**  
          764285-B21
      
      **New features in firmware version 2.42.5000:**
      
        * Added support for the following features. 
          * new TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * A mechanism to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
          * A new field is added to "set port" command which notifies the firmware what is the user_mtu size.
        * Improved the debug ability for command timeout cases.
      
      **New features and changes in firmware version 2.42.5700.**
      
        * Modified the mlx_cmd_get_mlx_link_status command return value to return "Link Type = Ethernet" in Ethernet adapter cards.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.12-2.1
changelog:
  -     *The following changes have been made in sub-version 1.0.12(A):**
      
        * Product rebuilt to have the new SHA 384 signature.
      
      **Fixes in version 2.42.5000:**
      
        * PortRcvPkts counter was prevented from being cleared after resetting it.
        * The system Timed Out on the configuration cycle of the Virtual Functions (VFs) when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hangs and results in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA, the RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * link did not go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Network Controller Sideband Interface (NC-SI) did not work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes in version 2.42.5056:**
      
        * Fixed an issue that resulted in reading from invalid I/O address on handover from UEFI boot to OS boot, when a port was configured as InfiniBand on a VPI adapter device.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     Security Hardening Enhancements: This release contains important reliability
      improvements and security hardening enhancements. HPE recommends upgrading
      your device's firmware to this release to improve the firmware security and
      reliability of your device.
      
      
      
      **New features and changes included in version 20.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below:
      
      QOS_TRUST_STATE_P1  
      QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
      TRUST_PORT  
      TRUST_PCP  
      TRUST_DSCP  
      TRUST_DSCP_PCP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *The following issues have been fixed in version 20.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * The RXT E2E inflight went into an unresposive state occasionally.
        * RDMA partition was reported even if NIC+RDMA mode was disabled.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * An incorrect address issue for XRQ Event Backend Controller Px Syndrome event in multi-host system during FLR.
        * PCIe SKP OS generation interval issue for Gen1 and Gen2.
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     Security Hardening Enhancements: This release contains important reliability
      improvements and security hardening enhancements. HPE recommends upgrading
      your device's firmware to this release to improve the firmware security and
      reliability of your device.
      
      **New features and changes included in version 20.36.1010:**
      
        * Enabled provisioning of the OEM public key that is used for OEM NVconfig file signature verification.
        * Enabled constant clock offset (visible using PPS out) when synchronizing the device using PTP in 25G or 10G port link speed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *The following issues have been fixed in version 20.36.1010:**
      
        * Aligned RDE behavior to DSP0266 v1.15.0  table 23.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3-4.1
changelog:
  -      This Firmware release contains various drive interoperability enhancements and code fixes accumulated since the last firmware release, as well as a change to disable MCTP over PCIe VDM function per requested of HPE, and a PHY setting change for improved compatibility with Intel Ice Lake based Gen10 Plus DL360 platform. 
        * For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00115201en_us


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3-5.1
changelog:
  -      Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK5
changelog:
  -      Fixed an incompatibility issue in MCTP over PCIe VDM function
        * Updated WCTEMP value for thermal throttling threshold


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-5.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-8.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      This update includes a fix that prevents unrecoverable read errors in highly localized write intensive workload, and a new servo code revision that improves performance under specific vibration conditions.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4ICDHPK1
changelog:
  -      This firmware corrects the potential for a drive to become disabled and nonfunctional during certain conditions or workloads.
        * After the drive is upgraded to firmware version HPK1, it cannot be downgraded to firmware version HPK0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4ICDHPK1-2.1
changelog:
  -      Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> GPK4
changelog:
  -      Fixes Get Endpoint ID (EID) command failure by issuing Set Endpoint ID after Endpoint Discovery


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-8.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location. This issue was only found during supplier ongoing reliability testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-4.1
changelog:
  -      The issue affects SSDs with an HPE firmware version prior to HPD8 that results in SSD failure at 32,768 hours of operation (i.e., 3 years, 270 days 8 hours), neither the SSD nor the data can be recovered, after the SSD failure occurs.
        * In addition, SSDs which were put into service at the same time will likely fail nearly simultaneously.
        * For more information, refer to HPE Customer Advisory at the following URL:<https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00092491en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      VENDOR IDENTIFICATION field change from "HP" to HPE". Support for second source PMIC from IDT.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK5-5.1
changelog:
  -      Optimized T-offset setting.
        * Change MQES setting to 8192.
        * Fixed LED Behavior misaligned specs issue.
        * Fixed performance drop issue when 4+ SSD are installed.
        * The Idle Power Management fix to keep the drive from entering and exiting the Lower Power Idle mode too frequently.
        * For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00112800en_us


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK6
changelog:
  -     Please refer to SID8624 wtih the reason that why upgrade requiremnet need to
      be set to Critical


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK6
changelog:
  -      Main fixes are for Secure boot(Option ROM) ILO error and critical fix for issue where failure to send MI command completion could result in drive reporting 0GB until power cycled.
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00123725en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. 
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. 
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      A low-probability, high severity corner case of sustained outer-diameter activity with emergency power off when heads are at the outer diameter prevented heads from parking/latching properly on a few drives in the field.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> GPK3
changelog:
  -     This Firmware release address below fixes and additional features:
      
        * FW Transfer Fix
        * Drive Failure Fix
        * Power Loss Protection
        * FW Download Fix
        * Reset Fix
        * Shutdown fix
        * PCIe Improvement
        * Random Write Improvement


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> GPK3-2.1
changelog:
  -      .Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-3.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -      Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-5.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-7.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Fix command timeout and uncorrectable error improvement.
        * Added features for SAS4 auto power swtiching and thermal requirement.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-3.1
changelog:
  -      Online firmware flashing of drives attached to aSmart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiantand Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like(B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-3.1
changelog:
  -      The issue affects SSDs with an HPE firmware version prior to HPD7 that results in SSD failure at 40,000 hours of operation (i.e., 4 years, 205 days 16 hours), neither the SSD nor the data can be recovered, after the SSD failure occurs.
        * In addition, SSDs which were put into service at the same time will likely fail nearly simultaneously.
        * For more information, refer to HPE Customer Advisory at the following URL:<https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00097382en_us>.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      This maintenance FW release addresses a rare corner case COMRESET issue at warm boot, and to address an early EOL behavior under certain use cases.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -     These firmware release add a foreground media scan policy to prevent a
      Predictive Failure and add SMART Attribute value for the FMS count.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -      Fixes the issue that certain SSDs may report false predictive failure in the integrated management log (IML).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -      This firmware fixes an issue that, under extremely rare conditions, can cause a data miscompare. It eliminates causes of some potential timeouts and hangs. It also addresses some temporary performance degradation conditions.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-2.1
changelog:
  -      This firmware release provides additional protection against command timeouts.
        * For more information, refer to HPE Customer Bulletin at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00117258en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3-2.1
changelog:
  -      This FW change resolves a MCTP VDM compliance issue seen by iLO version 2.30.
        * For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00111061en_us


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-7.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location. This issue was found during supplier ongoing reliability testing.
        * The firmware also includes emergency power off improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> EPK75H3Q-3.1
changelog:
  -      Fixed False UECC issue at idle power mode.
        * Old FW download Blocking (EPK70H3Q~EPK74H3Q).
        * FW is changed off the option of TX data alignment for each lane.
        * FW is changed to clear the interrupt after TLP Complete when PCIe config read operation.
        * For more information, refer to HPE Customer Bulletin at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00113342en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> EPK76H3Q
changelog:
  -      Contains critical fix for issue where failure to send MI command completion could result in drive reporting 0GB until power cycled.
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00123725en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4IASHPK3
changelog:
  -      Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4IASHPK3-2.1
changelog:
  -      Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Reverted OCP spec features to maintain compliance to OCP spec commands over NVMe-MI
        * Implemented real Active Measured Latency by adding OCP 2.0 C3 Log page


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-6.1
changelog:
  -      This code corrects a potential data integrity issue related to unaligned write commands.This issue was only found in supplier ongoing lab testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-8.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location. This issue was found during supplier ongoing reliability testing.
        * The firmware also corrects settings preservation after a code download, and includes emergency power off improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 85031G00
changelog:
  -      This is a maintenance release that contains various drive reliability enhancements and code fixes accumulated since the last initial release, as well as a change to disable MCTP over PCIe VDM function to satisfy certain HPE platform environments.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 85032G00
changelog:
  -      Implements FW-based VPD.
        * ARP setting is changed from "Capable & Discoverable" to "Fixed & Discoverable".
        * A minor tweak to the Foreground Media Scan (FMS) algorithm to ensure critical variables are initialized properly.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -     This firmware fixes a potential reliability condition, a rare data integrity
      issue and the cause of a potential hang.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Improves data integrity
        * Decreases possibility of data corruption in certain error and timing conditions
        * Reduces the probability of hangs


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     This firmware revision corrects a rare situation where a Cryptographic Erase
      could result in random data instead of the expected deterministic zeros. This
      is judged as low severity because it does not compromise user data or
      security, but justifies the update to preclude potential security concerns.
      There are several items that reduce the probability of hangs and provide some
      minor performance improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDA
changelog:
  -      This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
        * The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
        * Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -     *Problems Fixed:**
      
        * Fixed an issue where wear usage was not being reported correctly in the SmartSSD Wear Gauge Utility


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      If Power On Hours exceeds 70,000hrs, PM2R will report Hardware error (04/4C/A8) after the next Power Cycle and will not accept read/write commands. This fix will update storage location reporting when the maximum number of registrations in the Work Load Log read process reaches 70,000; the last registered 70,000th storage location will be modified to be read as the next (70,001st) storage location.
        * For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00111296en_us


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -     This firmware fixes a condition that could cause the heads to land on the
      media in an emergency power off situation, and eliminates a command timeout
      issue. Some internal logging operations were refined at the same time.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Provides proactive protection against contamination built up on the media and air-bearing surface of the heads by increased routine "sweeping" of the media surface.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -     This FW release deploys an Enhanced Media Scan algorithm that addresses an
      issue when the host system does not provide enough idle time for drive's
      Foreground Media Scan to be activated, which is needed to ensure long term
      drive reliability. It also addresses few minor issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      Applied enhanced NAND recovery algorithm to prevent read UECC error
        * Prepare proper response data for Get Message Type Supported MCTP Command


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      The updates were included in a regularly scheduled 5300 maintenance release. This firmware has a security version upgrade to include TCGe SKUs and prevent a downloading of a back level firmware version of HPG0 after upgrading to HPG1.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-2.1
changelog:
  -      Reduced the occurrence probability of PMIC busy issue. 
        * Fixed the system data error at the drive power on issue. 
        * When the PLP operation starts, the waiting Unmap request to the 4KB not-aligned host write area is canceled to be able to complete PLP correctly.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4ICRHPK3-2.1
changelog:
  -      The issue affects SSDs with an HPE firmware version prior to 4ICRHPK3 that may result in SSD failure starting at 4,700 hours of operation, neither the SSD nor the data can be recovered, after the SSD failure occurs.
        * For more information, refer to HPE Customer Bulletin at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00111900en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Improved Product Quality and Reliability. Changed Cap Charge Timeout to 14 seconds from 4 seconds to provide additional time for cap charge in marginal power environment.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc...


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. 
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. 
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      This firmware version updates the Vendor ID in the standard inquiry to 'HPE', in previous versions it was 'HP.'


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-2.1
changelog:
  -      Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-5.1
changelog:
  -      Fixes a rare link loss issue and adds enhancements for drive reliability.
        * After HPG5 firmware is downloaded to the drive, the new HPG5 firmware will be active on the drive.
        * The new drive bootloader code will be activated after the next drive power cycle.
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00072768en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     This firmware version updates the Vendor ID in the standard inquiry to 'HPE',
      in previous versions it was 'HP.'


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4-3.1
changelog:
  -      Fixed timing issue to pass VMWare VSAN certification.  Downgrading to any previous version of firmware is not allowed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8
changelog:
  -      Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -     This firmware fixes a condition that could cause the heads to land on the
      media in an emergency power off situation, and another condition that can lead
      to high-fly write, and eliminates a command timeout issue. Some internal
      logging operations were refined at the same time.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode  is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode  is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      Improvement in mixed READ/WRITE performance, which was causing a field issue at an HPE customer


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      Improvement in mixed READ/WRITE performance, which was causing a field issue at an HPE customer - Improve random mix performance in TL=2048k and 512k


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      Fixes an issue where the SSID was not programmed correctly to the drive. This may cause issues with the drive not being identified correctly in the Integrated Lights Out Utility.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3
changelog:
  -      Fixed SSD weargauge report error issue.
        * Fixed Assign FWState as TR_DONE_ERR at the correct location.
        * Prepare proper response data for Get Message Type Supported MCTP Command.
        * Added code to preserve current feature values cross live firmware update.
        * Allocate 4 bytes instead of 2 bytes for parameter code.
        * Changed the value for NLB equal to NSize -1.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Addresses a hot plug reporting concern
        * Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      This firmware provides a change to the Vendor ID in the VPD page that refers to HP instead of HPE.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Improves data integrity
        * Decreases possibility of data corruption in certain error and timing conditions
        * Reduces the probability of hangs and provide a minor performance improvement


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> MPK75H5Q-4.1
changelog:
  -      Fixed False UECC issue at idle power mode (12.8TB and 15.36TB only).
        * Apply PCLK running PHY option, PLL clock disable can be avoided in lane 0 missing case.
        * Old FW download Blocking.
        * FW is changed off the option of TX data alignment for each lane.
        * FW is changed to clear the interrupt after TLP Complete when PCIe config read operation.
        * For more information, refer to HPE Customer Bulletin at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00113342en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-7.1
changelog:
  -      Fixes a data integrity risk where stale data is mistakenly used from cache.
        * Fixes a data integrity risk where stale data is returned on an unaligned overlapped write-read operation.
        * Fixes a data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      There is no compelling reason to update this firmware. Risk is that whoever looks at the Vendor ID in the VPD page will notice that it refers to HP instead of HPE. There is no functional risk if not upgraded.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      This firmware release provides additional protections against hangs in certain corner cases, and cleans up some error handling and command behavior issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.6.1
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later
      
      **Problems Fixed:**
      
      Addressed an issue where the Integrated Lights-Out (iLO) web interface may
      incorrectly report the Innovation Engine is running in a degraded state.
      
      Addressed an issue where memory telemetry data may not be reported properly in
      the Integrated Lights-Out (iLO) web interface or through the HPE RESTful API.
      
      Addressed an issue where the Innovation Engine Firmware flash would fail if a
      previous flash attempt was interrupted and not completed successfully.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.6.1-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 0.1.6.1(C) contains updates to the component packaging and is
      functionally equivalent to ver. 0.1.6.1.  It is not necessary to upgrade with
      Revision C if a previous component Revision was used to upgrade the firmware
      to version 0.1.6.1.
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later  
      
      **Problems Fixed:**
      
      Addressed an issue where the Integrated Lights-Out (iLO) web interface may
      incorrectly report the Innovation Engine is running in a degraded state.
      
      Addressed an issue where memory telemetry data may not be reported properly in
      the Integrated Lights-Out (iLO) web interface or through the HPE RESTful API.
      
      Addressed an issue where the Innovation Engine Firmware flash would fail if a
      previous flash attempt was interrupted and not completed successfully.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.0.11
changelog:
  -     Added support for Intel Xeon Scalable Performance 3200, 4200, 5200, 6200 and
      8200 series processors.
      
      Added support for HPE system performance monitoring and workload performance
      advisor. This feature also requires Integrated Lights-Out (iLO) firmware
      version 1.40 or later.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.0.11
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where updates to the Intel Server Platform
      Services (SPS) firmware may fail.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.1.2-2.1
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Added support for HPE Persistent Memory featuring Intel Optane DC Persistent
      Memory.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.2.0
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where Processor or Memory temperature
      reporting may not be collected properly by the platform and the system fans
      may be running faster than expected. This issue has been seen occasionally
      after a server reboot and is typically corrected with a subsequent server
      reboot.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.2.2
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where processor or memory temperature
      reporting may stop reporting properly or report a constant reading after
      servers have been operating over an extended period of time without an AC
      power cycle.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.2.3
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Address an issue where Innovation Engine (IE) Firmware may be unresponsive and
      iLO Firmware may report "Update Failed" after flashing the Innovation Engine
      (IE) Firmware via RESTful update.  The flash will have been performed
      successfully, but the system must be reset for IE Firmware to function
      properly.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.3.0
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours. On some systems this could result in a brief drop in CPU utilization or
      network traffic lasting less than a second.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.3.0-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 0.2.3.0(C) contains updates to the firmware packaging and is functionally
      equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision B if
      a previous component revision was used to upgrade the firmware to version
      0.2.3.0.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours. On some systems this could result in a brief drop in CPU utilization or
      network traffic lasting less than a second.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0.22
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0.22-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.0.22(C) contains updates to the firmware packaging and is
      functionally equivalent to ver. 1.0.0.22. It is not necessary to upgrade with
      Revision B if a previous component revision was used to upgrade the firmware
      to version 1.0.0.22.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.81
changelog:
  -      Not clearing error in processing interrupts can lead to interrupt storms leading to firmware watchdog reset 
        * RDE Changes to create Location URI for newly created resource when LRT is completed
        * RDE client MC error code mapping is wrong
        * iLO FW Communication Issue 1) iLO cannot be accessed via Web UI AND/OR 2) Ilorest commands slow/unresponsive post upgrade to iLO version 2.78
        * Server fails to power up as secure start did not complete successfully


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.90
changelog:
  -       Handle Devices reconnection when Bus Device Function information has changed after the Device comes back after Reset. 
        *  Enhancements to ensure Simplified Compute Ops Management onboarding. 
        *  Logging Improvements in Compute Ops Management.
        *  Implemented a flag that allows autoconnection to Compute Ops Management after reboot.
        *  Handle Type - A Firmware Update gracefully even when iLO goes for a reboot. 
        *  Handle Reset scenarios gracefully when updating via Compute Ops Management instead of abruptly going for a reset component gets updated.
        *  Enable/disable SNMP v1 and v3 independently


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.90
changelog:
  -        UEFI iLO config utility lets users add special characters to the ILO hostname
        *   Over Temperature alerts observed with Pensando Cards.
        *   CEC FW Version not seen on iLO 5.
        *   Discrepancy observed in the Current Operating Power comsumption data
        *   Incorrect CPU throttling information observed in iLO.
        *   Incorrect HPE DIMM part number in ERS memory Event.
        *   iLO incorrectly reports missing PSUs and sensor readings.
        *   iLO incorrectly shows connected to Compute Ops Management though connection is not established.
        *   System shuts down when updating Intelligent Provisioning and SPP.
        *   Issues observed on iLO with DL360 Gen10 Server and NVMe SSD Boot drives combination.
        *   Thermal policy is not spinning up fans in some cases resulting in inadequate air flow.
        *   Local User Passwords containing a backslash character may not be set correctly in the iLO 5 Command Line Interface
        *   Organizational Unit attribute is mandatory for the iLO Redfish REST API for generating a CSR whereas in the UI it is marked Optional.
        *   Automatic Certificate Enrollment may not work if the Certificate Authority signing the iLO Certificate Signing Request is an Intermediate.
        *   SPP/SUM Nutanix DX380 (Gen10): Intermittent Issue Updating IE and SPS FW from SPP2022.03.0 - Duplicate of "Intelligent Provisioning and Manageability Engine Firmware fails to get updated intermittently."
        *   "Trap Source Identifier" setting periodically changes to "iLO Hostname" from previously defined "OS Hostname"
        *   IE not updating due to incorrect Target GUID
        *   Caution Threshold and Critical Threshold reported on Memory Temperature sensor of NVIDIA A100-SXM4-80GB


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.91
changelog:
  -     iLO 5 v2.91 has the same content or feature set as iLO 5 v2.90 plus an
      additional fix for COM (Compute Ops Management) related to COM4VC bundle
      update message and event. The additional COM related fix is NOT applicable to
      other regular use case scenarios. Hence upgrading to iLO 5 v2.91 is optional.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.91
changelog:
  -     Fix provided to have synchronous messages to reflect the status, to Compute
      Ops Management, after completion of server reset during bundle update in
      COM4VC use case scenario.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.95
changelog:
  -     \- Added capability in iLO for Two Factor Authentication using OTP (One Time
      Password) for Microsoft AD users  
       \- To display drive enclosure info in Firmware tab in iLO  
       \- Support for controller which goes for functional reset runtime  
       \- iLO to mark the correct component update status for runtime agent
      updatable components based on the update status and update result  
       \- Secure erase of data based on the usecase (customer, factory or openbmc
      ownership transfer)  
       \- iLO stops the bundle update in the scenario where BootToUefi task goes to
      exception to ensure Graceful shutdown of server  
       \- iLO Support for OBSE in factory mode without the need for Advance License  
       \- Added support for comma (",") as a delimiter for multiple email IDs in
      AlertMail feature


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.95
changelog:
  -     \- OEM iLO component does not show the OEM equivalent entry for Intelligent
      Provision in One Time Boot Option  
      \- Handling delayed device discovered in UEFI mode during discovery phase  
      \- Persist the KCS interface setting across iLO reboots  
      \- Capability to enable KCS interface setting without needing a factory reset


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.1
changelog:
  -      This product addressed the disconnection with iLO after switching to Shared Network mode.
        * This product addressed the compatibility of shared memory communication on adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12.1
changelog:
  -      This product addresses an issue a packet missing problem after some amounts of multicast UDP streams transmitted.
        * This product addresses an issue the port identifier LED problem on HPE Ethernet 10Gb 2-port 535T Adapter .


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.13.0
changelog:
  -     This product no longer supported of updating FW via Service Pack for Proliant
      on HPE Proliant Gen9 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.13.50
changelog:
  -     This product addresses an issue about battery POST error caused by unnecessary
      protocol on Supported Devices of this product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.14.0
changelog:
  -      This product addresses an issue incorrect reporting on link status of HPE 631FLR-SFP28 Adapter.
        * This product addresses an issue battery POST error caused by unnecessary protocol on Supported Devices of this product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15.2
changelog:
  -      This product enhances bnxtnvm support OTP programming.
        * This product enhances coredump support to dump  cache contents.
        * This product enhances Firmware command line module modularity
        * This product enhances to add support for disabling Overflow detection for CQs (Completion Queues) of RoCE (RDMA over converged Ethernet )
        * This product enhances FW support for QUIC key (Quick UDP Internet Connection) context backing store management
        * This product enhances to add support for PCIe TPH (TLP Processing Hints)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15.2
changelog:
  -      This product correct an issue which not allow the user to configure the multi-function mode option with option value string.
        * This product correct an issue which the performance issue is seen with GRO offload (Generic Receive Offload) enable.
        * This product correct an issue which the Firmware upgrade fails if bnxtnvm uses the default value.  increased the timeout value to sufficient vaule.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.16.2
changelog:
  -      This product enhances the RDE BEJ encoding for some MessageArgs.
        * This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
        * This product removes Energy-Efficient Ethernet (EEE) from the PHY.
        * This product adds range validation checks to dest_port and dest_port_mask for ntuple commands.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.16.2
changelog:
  -      This product fixes the issue of incorrect PCIe VF numbers caused by some NCSI queries.
        * This product fixes the RDE error response for certain properties with unsupported input
        * This product fixes the problem of no RDE alert being generated when the link status changes.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.28.60
changelog:
  -     This product now supports the following network adapters:
      
        * Broadcom BCM5719 Ethernet 1Gb 4-port Base-T Adapter for HPE
        * Broadcom BCM5719 Ethernet 1Gb 4-port Base-T OCP3 Adapter for HPE


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.31.0
changelog:
  -     This product addresses an issue the adjustment of firmware read-write commands
      on corresponding OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.32.3
changelog:
  -     This product correct an issue which the Boot Code Version of the Firmware did
      not get updated after upgrading the Firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33.3
changelog:
  -      This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
        * This product adds to support HPE MicroServer Gen11


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33.3
changelog:
  -      This product fixes the intermittent issue of displaying incorrect device status under iLO web
        * This product fixes the intermittent lost iLO connection with shared networking mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.1
changelog:
  -      This product addressed a problem where Reboot Required option was not set after doing firmware update under RBSU.
        * This product addressed the disconnection with iLO after switching to Shared Network mode on BCM5719 OCP3 adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.50
changelog:
  -     This product addresses an issue where the FAN behavior with installed BCM 5719
      1Gb 4p BASE-T OCP Adptr.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.1
changelog:
  -     *Changes and New Features in version 1.8.1.0.0 :**
      
        * Added hfi1_eprom **v10_8_0_0_13.**
        * Loader ROM **HfiPcieGen3Loader_1.8.1.0.0.rom** and driver EFI **HfiPcieGen3_1.8.1.0.0.efi** were added.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.0
changelog:
  -     *Fixes included in version 1.11.0:**
      
        * **The following issue has been fixed in Unified Extensible Firmware Interafce (UEFI) ROM: **On some platforms, the hfi1 device was not showing up in BIOS/UEFI boot menus and was not available as a PXE boot device. This was caused by the platform not loading the UEFI driver for the hfi1 adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12.0-2.1
changelog:
  -     *Fixes included in version 1.12.0:**
      
        * Fixed race condition between BIOS checking link status and LNI completing which resulted in PXE boot failures.
        * Changed the default behavior of the hfi1_eprom tool to convert the eprom format to version 2, eliminating the need to supply the -N command line argument.
        * Addressed an issue where updating the HfiPcieGen3Loader*.rom file could result in the erasure of HfiPcieGen3Loader*.efi and HFI_TYPE1*.dat files.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.6
changelog:
  -     This product now supports Red Hat Enterprise Linux 8 update 4 and SUSE Linux
      Enterprise Server 15 Service Pack 3


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.50
changelog:
  -      This product addresses an issue where link flipping is seen with HPE Ethernet 10Gb 2-port 568FLR-MMSFP+ Adapter.
        * This product addresses an issue where the link speed isn't consistent with HPE Ethernet 10Gb 2-port 568FLR-MMT Adapter when system shutdown.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.0
changelog:
  -      This product addresses an issue where SR-IOV high latency is seen with HPE Ethernet 10Gb 2-port 562SFP+ Adapter and HPE Ethernet 10Gb 2-port 562FLR-SFP+ Adapter.
        * This product addresses an issue where it fails to disable HP Ethernet 1Gb 2-port 361i Adapter in RBSU.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.35
changelog:
  -     This product addresses a issue where IGMP2 packets isn't forwarded to the host
      OS when shared NIC is enabled with HPE Ethernet 1Gb 2-port 361i Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.27.0
changelog:
  -      This product addresses an issue where Option ROM version is missing with some Intel 1GB adapters
        * This product addresses an issue where disconnection occurs after rebooting system with HPE Ethernet 1Gb 2-port 368i Adapter and HPE Ethernet 1Gb 4-port 369i Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.27.30
changelog:
  -     This product addresses an issue where NIC status(iLO page->System
      Information->Network) for HPE Ethernet 10Gb 2-port 562SFP+/562FLR-SFP+ Adapter
      is Unknown with being plugged in to a network.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.28.0
changelog:
  -     This product addresses an issue where the firmware installation exceeds the
      expected time by using Oneview to update Firmware with 568FLR-MMSFP+.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.55
changelog:
  -     This product addresses an link issue for Intel X710-DA2 Ethernet 10Gb 2-port
      SFP+ OCP3 Adapter for HPE.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.50
changelog:
  -      This product addresses an issue where the incorrect translation is seen with Intel Intel I350-T4 Ethernet 1Gb 4-port BASE-T  Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.25.4
changelog:
  -     This product addresses an issue where the adaters isn't recongized with HPE
      Ethernet 10Gb 2-port SFP+ OCP3 X710-DA2  Adapter and HPE Ethernet 10Gb 2-port
      SFP+ X710-DA2 Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Fixes in version** **14.26.XXXX :**
      
        * Fixed an issue that caused a function to misbehave when a PCIe Transaction Layer Packet (TLP) was set with a poisoned indication.
        * Fixed a rare issue that resulted in "destroy mkey " command getting stuck when rebooting the hypervisor.
        * The total firmware reset time is increased by 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Firmware for the following device is updated to 14.27.4000:**
      
      P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **Following New features and Changes are included in version 14.27.4000:**
      
        * Added mlxconfig support for power reduction: PCI CAP AUTO_POWER_SAVE_LINK_DOWN 
          * PCI CAP
          * AUTO_POWER_SAVE_LINK_DOWN
        * Added the following segments, as appeared in the PRM, to the Resource Dump: 
          * PRM_QUERY_QP
          * PRM_QUERY_CQ
          * PRM_QUERY_MKEY
          * QUERY_VNIC_ENV


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Following issues have been fixed in version 14.27.4000:**
      
        * An issue that caused the sent packet to hang while the device entered FLR mode.
        * Enabled Bar configuration bytewise by applying the write_en bitmask.
        * A rare case where the the device froze while running the sw reset flow under heavy stress and with many open resources.
        * Low PXE performance while using the VSC to trigger the send_ring_doorbells.
        * An error that prevented the completions (CQ) from being completed due to a race condition in the firmware transport error handlers, and the error stressors, where the error stressors would hang the firmware transport error handler flow.
        * An issue that caused the fragmented IP packets to drop was fixed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Firmware for the following device is updated to 14.28.1002:**
      
      P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **Following New features and Changes are included in version 14.28.1002:**
      
        * Added mlxconfig support for power reduction: PCI CAP AUTO_POWER_SAVE_LINK_DOWN 
          * PCI CAP
          * AUTO_POWER_SAVE_LINK_DOWN
        * Added the following segments, as appeared in the PRM, to the Resource Dump: 
          * PRM_QUERY_QP
          * PRM_QUERY_CQ
          * PRM_QUERY_MKEY
          * QUERY_VNIC_ENV


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Following issues have been fixed in version 14.29.1016:**
      
        * An issue that caused the sent packet to hang while the device entered FLR mode.
        * Enabled Bar configuration bytewise by applying the write_en bitmask.
        * A rare case where the the device froze while running the sw reset flow under heavy stress and with many open resources.
        * Low PXE performance while using the VSC to trigger the send_ring_doorbells.
        * An error that prevented the completions (CQ) from being completed due to a race condition in the firmware transport error handlers, and the error stressors, where the error stressors would hang the firmware transport error handler flow.
        * An issue that caused the fragmented IP packets to drop was fixed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Firmware for the following device is updated to 14.31.1014:**
      
        * P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **New features and changes included in version 14.31.1014:**
      
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Following issues have been fixed in version 14.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1014:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following device has been updated to 14.32.1010:**
      
        * P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6-2.1
changelog:
  -     *The following changes have been made in sub-version 1.0.6(A):**
      
        * Product rebuilt to have the new SHA 384 signature.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.15-2.1
changelog:
  -     *Fixes included in  firmware version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.31.1200:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1200:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.
      
      **The following issues have been fixed in version 16.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * An assert that was caused when trying to open 1024 functions on the device and the maximum number of functions was 1023.
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to hang.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
      
      **Additional Fixes included in version 16.31.1014:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.16
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.32.1010:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.32.1010:**
      
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for QSHR access register to enable Set and Query rate limit perhost per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.16
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * The system could not create more than 128K QPs.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
        * PCIe lane margining capability issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.17
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.33.1048:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter.
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.17
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.33.1048:**
      
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * The card occasionally masked some PCIe AER reporting.
        * Incorrect flow of credits blockage that prevented booting during DC cycle test.
        * An issue with BMC medium migration from SMBUS to PCIe, and increased FIFOs to pass large packets in case of the migration.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.18
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.34.1002:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.34.1002:**
      
        * Added LLDPEnable, LLDPTransmit and LLDPReceive properties to the RDE Port schema implementation.
        * Added "Command Unsupported" response code in cases when running the MCTP control command "Get Vendor Defined Messages Supported", and there were no supported VDMs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.18
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.34.1002:**
      
        * An issue where set_flow_table_entry failed when aso_flow_meter action was used.
        * A race condition that occured between the duplicate read and QP commands (2RST, 2ERR and Destroy) in the signature that caused the command to hang.
        * When all traffic applications sharing the same combination of <function, priority, side> were rate limited (for example by congestion control), this limit was enforced on other applications with different combinations of <function, priority, side> under the same VL. For example, requestor flows (RDMA-write) were limited to rate X, however, this rate was also enforced on a QP sending RDMA-read responses. This firmware version prevents rate limit enforcement on traffic applications which should not be limited.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.19
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.35.1012:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.19
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * Bad configuration of number of VFs and SFs led to the consumption of too many functions and triggered a FW assert 0x888E. The reduction flows behavior was fixed to ensure the configuration does not exceed the total number of supported functions. 
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.20
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      **The following issues have been fixed in version 16.35.3006:**
      
        * Packet loss that occurred when restarting the transmit. 
        * An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
        * A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
        * Added a missing VLAN strip.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues have been fixed in version 20.29.1016:**
      
        * Changed the default value of DCQCN's (Data center- Quantized Congestion Notification) NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        * An issue that prevented VXLAN packets with svlan/cvlan tag from being matched.
        * The eth_wqe_too_small counter to count ODP (On-Demand Paging) page used to fail.
        * An issue related to raising 100GbE link on ConnectX-6 VPI 100Gb/s adapter cards.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs are configured, VM restart (VF/PF FLR) will take longer than when MKEY_BY_NAME is disabled.
        * Low performance occurred after enabling the RoCE Accelerator capability.
        * On rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *Firmware for the following devices are updated to 20.31.1014:**
      
      HPE InfiniBand HDR/Ethernet 200Gb 1-port 940QSFP56 x16 Adapter - P06154-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 1-port 940QSFP56 x16 Adapter - P06250-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 2-port 940QSFP56 x16 Adapter - P06251-B21
      
      **New features and changes included in version 20.31.1014:**
      
        * NIC scheduling feature support has been disabled for non-privileged functions.
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * Updated the NC-SI speed reporting output to support 200GbE speed. Now when running the NC-SI command, the output presents 200GbE speed as well.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Asymmetrical MSIX Configuration: This feature allows the device to be configured with a different number of MSIX vectors per physical PCI functions.To use this feature, please follow these steps: 
          * Clear NUM_PF_MSIX_VALID to disable global symmetrical MSIX configuration.
          * Set PF_NUM_PF_MSIX_VALID to enable asymmetrical per Physical Function MSIX configuration.
          * Configure PF_NUM_PF_MSIX per physical PCI function.
        * RDMA partitioning and RDMA counters in IB mode.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.
        * Enabled UID 0 to create resources with UMEM (User Memory).
        * Receiving and sending native IB packets from/to the software (including all headers) via raw IBL2 QPs.
        * RX RDMA NIC flow table on an IB port. Now the software can steer native IB packets to raw IB receive queues according to the DLID and  the DQPN.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *The following issues have been fixed in version 20.31.1014:**
      
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to unresponsive state.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
        * In InfiniBand non-virtualization system, due to a corrupted steering root, traffic fails after a warm reboot.  
      
                                                                               
      **Additional Fixes included in version 20.31.1014:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.            
        * Improved PortXmitWait IB counter accuracy.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *Firmware for the following devices has been updated to 20.32.1010:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06251-B21
      
      **New features and changes included in version 20.32.1010:**
      
        * Added support for blocking unwanted GMP classes by dedicated MADs.
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Added a Congestion Control Key to all Congestion Control MADs to authenticate that they are originated from a trusted source.
        * Added an SMP firewall to block the option of sending SMPs (MADS sent on QP0 from the Subnet Manager) from unauthorized hosts to prevent fake SMPs from being recognized as the SM.
        * Vendor Specific MADs Class 0x9 is no longer supported by the firmware. If case the firmware detects such MAD, the firmware will return a "NOT SUPPORTED" error to the user.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for dynamic timeout mechanism when in InfiniBand mode.
        * Added support for QSHR access register to enable Set and Query rate limit per-host per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Added support for asymmetrical VFs per PF. To enable it: PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a none zero value.
        * Added 2 new MAD access registers to enable mlxlink to read/write access registers by LID (to the whole subnet).
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.
        * Limited the external loopback speed according to the used module's capabilities.
        * Modified the Effective BER calculation method. Due to this, the value of the Effective BER will be slightly higher, however the link quality remains the same as prior to this change.
        * This firmware version includes the following PCIe changes: 
          * Fixed the ACS Port Number field in DSPs and ACS Egress Control Vector field in DSPs.
          * Added support for VSC on USP of PCIe Switch.
          * Fixed the mapping of Legacy Interrupts in the PCIe Switch.
          * Fixed MRRS & MPS configurations in DSPs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *The following issues have been fixed in version 20.32.1010:**
      
        * System could not create more than 128K QPs.
        * Incorrect indication of the PCIe link down in the AER registers on PCIe switch upstream port.
        * Invalid RNR timeout when trying to set it during the rts2rts_qp transition.
        * The flash frequency on boot was lower than expected (under 50Mhz). The issue was fixed by enabling the firmware to increase it on boot2 to normal frequency.
        * A race condition between DC QP flush and DC packets that led to stuck slices in the hardware. To avoid such situation, firmware keeps the TCU drop set until QP flush is done.
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Firmware for the following devices has been updated to 20.33.1048:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21
      
      **New features and changes included in version 20.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation. 
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter. 
        * Crypto features can be in either wrapped or unwrapped mode. Meaning, the key can be wrapped or in plaintext when running the CREATE_DEK PRM command. To comply with the requirements specified in FIPS publication, all the created DEKs must be wrapped.  
      This feature adds new NV_CONFIG per device to control this mode, and enables
      the user to change all the crypto features to wrapped or cleartext.
      
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *The following issues have been fixed in version 20.33.1048:**
      
        * An issue where RDMA write may experience performance degradation when working with Adaptive Routing and DCT half-handshake mode.
        * An issue that ignored the default value of TX_SCHEDULER_BURST when its value in the ini was different than "0".
        * Implemented SLD detection code. Surprise Down Error Reporting Capable value was changed from 1 to 0 in boards where the downstream perst was not controlled thus causing SLD detection not to function properly.
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * RDMA_WRITE traffic performance degradation that occured when working with DC on Adaptive Routing network.
        * Bad cache invalidations of destroyed QPs.
        * A rare case where asserts and ext_synd appeared in dmesg after performing driver restart. 
        * An issue related to host isolation on multi-host systems.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *Firmware for the following devices has been updated to 20.35.1012:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21
      
      **New features and changes included in version 20.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP
        * Added support for using SetEventReceiver PLDM command with mode polling.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *The following issues have been fixed in version 20.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * The RXT E2E inflight went into an unresponsive state occasionally.
        * RDMA partition was reported even if NIC+RDMA mode was disabled.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * An incorrect address issue for XRQ Event Backend Controller Px Syndrome event in multi-host system during FLR.
        * PCIe SKP OS generation interval issue for Gen1 and Gen2.
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.
        * PLDM AEN event receiver was required to be cleared on PCIe reset in case the media type was MCTP over PCIe VDM.
        * Asynchronous messages were sent over MTCP before endpoint discovery was done.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *The following issues have been fixed in version 14.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1014:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.
      
      
      
      **The following issues have been fixed in version 14.31.1200:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1200:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.  
      
      
      **The following issues have been fixed in version 16.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * An assert that was caused when trying to open 1024 functions on the device and the maximum number of functions was 1023.
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to hang.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
      
      **Additional Fixes included in version 16.31.1014:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.32.1010:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.32.1010:**
      
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for QSHR access register to enable Set and Query rate limit perhost per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * The system could not create more than 128K QPs.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
        * PCIe lane margining capability issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.33.1048:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter.
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.33.1048:**
      
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * The card occasionally masked some PCIe AER reporting.
        * Incorrect flow of credits blockage that prevented booting during DC cycle test.
        * An issue with BMC medium migration from SMBUS to PCIe, and increased FIFOs to pass large packets in case of the migration.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.34.1002:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.  
      
      
      **New features and changes included in version 16.34.1002:**
      
        * Added LLDPEnable, LLDPTransmit and LLDPReceive properties to the RDE Port schema implementation.
        * Added "Command Unsupported" response code in cases when running the MCTP control command "Get Vendor Defined Messages Supported", and there were no supported VDMs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.  
      
      
      **The following issues have been fixed in version 16.34.1002:**
      
        * An issue where set_flow_table_entry failed when aso_flow_meter action was used.
        * A race condition that occured between the duplicate read and QP commands (2RST, 2ERR and Destroy) in the signature that caused the command to hang.
        * When all traffic applications sharing the same combination of <function, priority, side> were rate limited (for example by congestion control), this limit was enforced on other applications with different combinations of <function, priority, side> under the same VL. For example, requestor flows (RDMA-write) were limited to rate X, however, this rate was also enforced on a QP sending RDMA-read responses. This firmware version prevents rate limit enforcement on traffic applications which should not be limited.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.35.1012:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.  
      
      
      **New features and changes included in version 16.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.  
      
      
      **The following issues have been fixed in version 16.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * Bad configuration of number of VFs and SFs led to the consumption of too many functions and triggered a FW assert 0x888E. The reduction flows behavior was fixed to ensure the configuration does not exceed the total number of supported functions. 
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.  
      
      
      **The following issues have been fixed in version 16.35.3006:**
      
        * Packet loss that occurred when restarting the transmit. 
        * An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
        * A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
        * Added a missing VLAN strip.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.7.16
changelog:
  -     This product corrects an issue where the firmware update fails when the first
      port is disabled on the network adapter.
      
      This product corrects an issue where not all devices are discovered as part of
      firmware update on a multi-root-complex platforms like Integrity, Superdome
      etc.
      
      This product corrects an issue where the system hangs during POST with red
      screen when iSCSI boot LUN is re-exported (after a previous unexport
      operation) from the iSCSI host (HPE 3PAR StoreServ Storage).
      
      This product corrects an issue where 'HPE Synergy 4820C 10/20/25Gb Converged
      Network Adapter' disappears after changing its link speed under its
      configuration menu (located at 'System Utilities'(F9 at POST)->'System
      Configuration').
      
      This product corrects an issue where the configuration settings of the
      adapter, connected to a server managed by OneView profile, may be reset to
      defaults after a system reboot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.12
changelog:
  -     This product now remove supports Synergy and Blade Server.
      
      This product now supports Red Hat Enterprise Linux 8.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.12
changelog:
  -     This product addresses an issue where 2nd port reports "function type:
      disabled" with HPE Ethernet 10Gb 2-port 524SFP+ Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.9.8
changelog:
  -      This product corrects the abnormal disconnection of iLO web page while performing under Shared Networking on Flexible-LOM.
        * This product addresses an issue where the HPE Ethernet 10/25Gb 2-port 622FLR-SFP28 adapter and  HPE Ethernet 10/25Gb 2-port 621SFP28 Adapter UMCE (Uncorrectable Machine Check Exception) was followed by Unrecoverable I/O error, Uncorrectable PCI express error on Server and one of the ports suddenly no longer can send or receive traffic.
        * This product addresses an issue where driver doesn't load upon booting up by correct memory relocation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.0
changelog:
  -     This product addresses an issue where the modification on string format of
      firmware update payload.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.21.3
changelog:
  -     This product now supports Red Hat Enterprise Linux 8 Update 6, Liunx 9 and
      SUSE Linux Enterprise Server 15 Service Pack 4.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.0
changelog:
  -     This product addresses an issue where Max Number of Virtual Machine
      Queues/Physical Function shows zero value in AHS


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.26.30
changelog:
  -     This product addresses an Overheat issue that system shuts down automatically
      due to NIC temperature exceeding threshold.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.27.8
changelog:
  -      This product corrects the display problem of the adapter name under RBSU.
        * This products corrects some issues about the thermal reporting and temperature threadshold control of the adapter.
        * This product addresses an issue where unexpected UMCE(Uncorrectable Machine Check Exception) appeared when powering on the system with NPAR(Network Partitioning) enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.27.50
changelog:
  -     This product addresses an issue where the Firmware installation failure when
      enabling secure boot under SUSE Linux Enterprise Server 15 SP2.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.28.50
changelog:
  -      **This product addressed the firmware update failure problem which may cause NIC FW corruption.**
        * **This product addressed the firmware update failure problem while the platform secure boot being enabled.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30.2
changelog:
  -      This product addresses a cosmetic change in the adapter configuration page to reflect that DCBx is enabled and as long as LLDP is enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.31.4
changelog:
  -     This product now supports Red Hat Enterprise Linux 8 Update 6, Liunx 9 and
      SUSE Linux Enterprise Server 15 Service Pack 4


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM version
      1.20 or later
      
      **Enhancements/New Features:**
      
      Added support for Dynamic Power Capping. For proper operation, please ensure
      that Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM
      version 1.20 or later are updated on the server.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.4 (B) contains support for new server products.  It is functionally
      equivalent to ver. 1.0.4.  It is not necessary to upgrade with Revision (B) if
      a previous component revision was used to upgrade the firmware to ver. 1.0.4.
      
      **Firmware Dependencies:**
      
      Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM version
      1.20 or later
      
      **Enhancements/New Features:**
      
      Added support for Dynamic Power Capping. For proper operation, please ensure
      that Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM
      version 1.20 or later are updated on the server.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-4.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.4 (D) contains updates to the component packaging and is functionally
      equivalent to ver. 1.0.4.  It is not necessary to upgrade with Revision (D) if
      a previous component revision was used to upgrade the firmware to ver. 1.0.4.
      
      **Firmware Dependencies:**
      
      Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM version
      1.20 or later
      
      **Enhancements/New Features:**
      
      Added support for Dynamic Power Capping. For proper operation, please ensure
      that Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM
      version 1.20 or later are updated on the server.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Added support for AMD EPYC 7002 Generation Processors. ROM version 2.00 or
      later is required to enable the support. This version of firmware does not
      include any changes for platforms with Intel Processors or AMD EPYC 7001
      Generation Processors.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.7 (B) contains updates to the component packaging and is functionally
      equivalent to ver. 1.0.7. It is not necessary to upgrade with Revision (B) if
      a previous component revision was used to upgrade the firmware to ver.
      1.0.7.This is the initial version for HPE Gen10 Plus servers.  
      
      
      **Firmware Dependencies:**
      
      For HPE ProLiant DL325/DL385 Gen10 servers, ROM version 2.00 or later is
      required to enable the support. iLO5 version 1.40 or above is required to
      upgrade to this version.
      
      **Enhancements/New Features:**
      
      Added support for AMD EPYC 7002 Generation Processors on HPE ProLiant
      DL325/DL385 Gen10 servers. ROM version 2.00 or later is required to enable the
      support. This version of firmware does not include any changes for Gen10
      platforms with Intel Processors or AMD EPYC 7001 Generation Processors. iLO5
      version 1.40 or above is required to upgrade to this version.
      
      This is the initial version for HPE Gen10 Plus servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.7 (C) contains updates to the component packaging and is functionally
      equivalent to ver. 1.0.7. It is not necessary to upgrade with Revision (C) if
      a previous component revision was used to upgrade the firmware to ver.
      1.0.7.This is the initial version for HPE Gen10 Plus servers.
      
      **Firmware Dependencies:**
      
      For HPE ProLiant DL325/DL385 Gen10 servers, ROM version 2.00 or later is
      required to enable the support. iLO5 version 1.40 or above is required to
      upgrade to this version.
      
      **Enhancements/New Features:**
      
      Added support for AMD EPYC 7002 Generation Processors on HPE ProLiant
      DL325/DL385 Gen10 servers. ROM version 2.00 or later is required to enable the
      support. This version of firmware does not include any changes for Gen10
      platforms with Intel Processors or AMD EPYC 7001 Generation Processors. iLO5
      version 1.40 or above is required to upgrade to this version.
      
      This is the initial version for HPE Gen10 Plus servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue of inaccurate temperature readings when the actual temperature
      exceeds 100 C on Proliant Gen10 Plus servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to
      upgrade to this version.
      
      **Problems Fixed:**
      
      Fixed an issue where the CPU may not restore to original working frequency
      after turning off Power Capping.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.0
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed a rare issue where CPU could become stuck at its lowest working
      frequency when dynamic power capping was enabled on AMD-based systems.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.10
changelog:
  -      To make Valid flag is always set to true initially so that CRC check can be performed on initstring partition and test if it is really valid.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.12
changelog:
  -     Users need to update HPE SAS 12G Expander FW version 5.12 for FW compatibility
      due to a specific SPI flash devices is used on the Expander card. Carry over
      issue resolution with reference SID8638.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.12
changelog:
  -     1\. In support of Micron 256Mb SPI ROM on the latest Shiner board
      
      2\. Provided a proper downgrade restriction to ensure FW compatibility with
      the latest HW


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.14
changelog:
  -     1. Fix intermittent expander/drives missing issue during repeatedly power cycles
        2. Provide a proper downgrade restriction to ensure firmware compatibility with the latest flashes


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.15
changelog:
  -      Add support of new flash on the latest expander board.
        * Provided a proper downgrade restriction to ensure firmware compatibility with the latest flashes.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56-2.1
changelog:
  -     *Note:** If version 1.56 was previously installed, then it is not necessary to upgrade to version 1.56 (B).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.00-2.1
changelog:
  -     *Note:** If version 1.00 was previously installed, then it is not necessary to upgrade to version 1.00 (B).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.26
changelog:
  -      In rare circumstances after multiple, successive reboots, a system with 28 large form factor drives might become unresponsive. Firmware v1.26 resolves the issue.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.26-2.1
changelog:
  -      Updated to support Service Pack for ProLiant version 2017.07.0
      
                **Note:** If version 1.26 was previously installed, then it is not necessary to upgrade to version 1.26 (B).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.79-2.1
changelog:
  -     Drive may show up missing after a system reboot.
      
      Please reference Customer Advisory a00098241en_us


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.39
changelog:
  -     It's the transition version before migrating to newer version 0.39(B). 0.39
      doesn't have any function change or issue fix, just to activate the new
      Product ID naming.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.39
changelog:
  -      It's the transition version before migrating to newer version 0.39(B). 0.39 doesn't have any function change or issue fix, just to activate the new Product ID naming.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.39-2.1
changelog:
  -      Modify Product ID to "A4200 Gen10P LFF" and "A4200 Gen10P SFF" to distinguish the different generation expander backplane.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.00
changelog:
  -      Fixed a rare problem where backup power status was incorrectly reporting Charging instead of Failed.
        * Fixed an issue where obsoleted SCSI pass through command fails.
        * Loss of redundant path message is incorrectly reported on logical drive failure with single domain configuration.
        * Fixed an issue where SmartPath may not be used after LUN Reset
        * Fixed a potential controller lockup 0x1BC0 during write then read I/O with drive URE's.
        * Fixed an issue that Apollo 4200 Gen10 plus LFF expander backplanes are not discovered by controller.
        * Fixed an issue that range locked SED failed with reason error erasing RAID metadata during reboot and remains failed after clear configuration.
        * Fixed an issue where the file system may read incorrect data from a degraded RAID 5 or 6 logical drive.
        * Fixed an issue where the file system or application may read incorrect data when a backup power source is discharged completely, and system power loss occurs during a transformation.
        * Fixed an issue where the drive Fault LED is not turned ON when firmware fails a bad HBA drive connected to an expander during device discovery or hot-plug.
        * Fixed an issue of auto-rebuild not starting if two drives fail at the same time on a RAID10 or RAID6 logical drive having only one "Auto-Replace Drives" spare drive.
        * Fixed an issue where the drive Fault LED is turned ON for a few seconds when multiple configured drives are hot removed from a SES enclosure and then hot added
        * Fixed an issue where rebuild did not start after multiple iterations of drive failures.
        * Fixed an issue where the controller might fail to discover devices after a cable is hot-added.
        * Fixed a potential problem of inability to delete a SmartCache write-back logical drive.
        * Fixed an issue where 0x1789 POST message error code is displayed as healthy and there is no information in HII when all logical drives in the controller are offline.
        * Fixed an issue where the last logical drive in an array cannot be deleted in UEFI configuration tool.
        * Fixed an issue where build method is not listed for RAID 6 array creation in UEFI configuration tool.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.00-2.1
changelog:
  -      Added support for DMTF PLDM Monitoring and Control for enhanced thermal monitoring
        * Added support for DMTF PLDM Redfish Device Enablement for Redfish Storage, StorageController, Port, Drive, Volume, & CollectionCapabilities
        * Added support for DMTF PLDM Redfish Device Enablement for Volume POST & DEL operations
        * Added support for DMTF Redfish StorageDevice.1.0.1 Events
        * Added support in firmware to enable logical drive transformation without backup power source on the controllers supporting data preservation.
        * Added support to return NCQ Priority Information for SATA drive to host.
        * Added support to blink the drive Predictive Failure (PF) LED during Predictive Spare Rebuilding (PSR) for drives that can be safely removed and replaced without causing a logical drive failure.
        * Added support to configure default setting for the drive write cache.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.61
changelog:
  -      Added support for for Local Key Management SED adapter password.
        * Added support for reporting surface scan metrics for SSA, SSACLI.
        * Added support for improving secure erase time for disks supporting the WRITE SAME command.
        * Added support for a new persistent event log policy that overwrites old events with the most recently occurred events.
        * Added support PLDM firmware update
        * Added support PLDM firmware update for UBM.
        * Enable Redfish Name property of Volume resource which is optional on create. The value is the same as DisplayName property.
        * Report VendorID, ProductID and location informations for enclosure SEPs.
        * Redfish POST request to perform the Drive.Actions.#SecureErase ACTION will be rejected with the extended error message ResourceInUse if the targeted Drive is a SED that is not in the original factory state(OFS).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.61
changelog:
  -      Fixed an issue where to create RAID 60 on 24 SATA SSDs resulted in controller lockup.
        * Fixed a performance drop issue on RAID 5 logical drives with 50/50 cache ratio on a 256K sequential read workload.
        * Fixed a parity inconsistency after RAID rebuild restarted with a new drive replacement.
        * Fixed an issue where a transforming logical drive fails when the controller is abruptly rebooted after logical drive deletion.
        * Fixed an issue where the logical drive failed during the heal array transformation.
        * Fixed an issue where rebuild does not start on an array with the spare disk.
        * Fixed an issue where the VDM requests were not being serviced in a timely manner when the controller was under high load.
        * Fixed controller lockup during clear configuration after SmartCache logical drive is moved from P-Series to E-Series controller.
        * Fixed an issue where not all permitted values were published to the WriteCachePolicy@Redfish.AllowableValues in VolumeCapabilities.
        * Fixed an issue where the VolumeCapabilities resource can be published with incorrect values for WriteCachePolicy@Redfish.AllowableValues when the controller's battery is charging.
        * Fixed an issue where the ControllerPasswordAccepted Redfish alert was sent with incorrect ControllerPasswordEntered messageId.
        * Fixed an issue where a drive's ServiceLabel is sometimes erroneously published with a leading zero on its Port number.
        * Fixed an issue where Redfish alerts generated early in the boot sequence were not reported to iLO.
        * Fixed an issue where a Redfish Volume create request is erroneously accepted when the request payload contains a WriteCachePolicy value conflicting with the existing cache configuration.
        * Fixed an issue where the ControllerPreviousError alert was sent with incorrect ControllerPreviouseFailure messageId and severity.
        * Fixed an issue where the BatteryCharging alert was sent with an incorrect severity on certain controllers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.01.04.339
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This image contains the latest Intel Server Platform Services (SPS) Firmware
      which contains mitigations for a variety of security vulnerabilities. The
      following vulnerabilities have been addressed in this SPS release:
      CVE-2019-11090 and CVE-2019-11109. These issues are not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.01.04.381
changelog:
  -     This image contains the latest Intel Server Platform Services (SPS) Firmware
      which contains mitigations for security vulnerability CVE-2020-0545. This
      issue is not unique to HPE Servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.01.04.381-2.1
changelog:
  -     *Important Notes:**
      
      The Ver. 04.01.04.381(B) flash component contains an updated flash image. The
      actual firmware is exactly the same as was delivered with the original ver.
      04.01.04.381 flash component. The previous flash component had an issue that
      caused flashing to intermittently fail. It is not necessary to upgrade with
      Revision B if a previous component Revision was successfully used to upgrade
      the firmware to version 04.01.04.381 or for systems that originally shipped
      with version 04.01.04.381 firmware.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where systems configured with older versions of the Server
      Platform Services (SPS) Firmware, such as version 04.00.00.288 or older, may
      become inoperable after flashing to SPS firmware version 04.01.04.381. This
      releases contains an updated flash component for SPS Firmware 04.01.04.381
      which allows direct flashing from older firmware versions to the latest.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.01.04.505
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2021.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This version of the Server Platform Services (SPS) Firmware addresses an issue
      where not all PCIe devices will be managed properly by the system when there
      are more than 16 PCIe devices present in the platform. This would include PCIe
      devices in PCIe slots or NVMe drives. This issue would typically manifest
      itself as iLO Firmware not properly reporting thermals from a device when a
      server was in this heavily loaded configuration.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.01.04.601
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2021.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with IPU.2021.2 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.01.04.804-2.1
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Addressed an issue where Intel reference systems were observed to
      intermittently fail to power on during extensive reboot testing.  This issue
      has not been reported on HPE servers.  This version of the Intel SPS firmware
      has been released as part of the Intel 2022.2 IPU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.04.04.058
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Added support for Intel Optane Persistent Memory.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.04.04.062
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version of the System ROM contains updates aligned with the INTEL Whitley
      BKC WW52.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 04.04.04.202
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the INTEL PLR3.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.52_10-28-2021
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of AMD security
      patch (AMD-SN-1021) which provides mitigations for BIOS advisories and
      security vulnerabilities documented as CVE-2020-12954, CVE-2020-12961,
      CVE-2021-26331, CVE-2021-26335, CVE-2021-26315, CVE-2020-12946,
      CVE-2020-12951. CVE-2021-26336, CVE-2021-26337, CVE-2021-26338,
      CVE-2021-26320, CVE-2020-12944, CVE-2020-12988, CVE-2021-26329,
      CVE-2021-26330, CVE-2021-26321, CVE-2021-26323, CVE-2021-26325,
      CVE-2021-26326, CVE-2021-26322, CVE-2021-26327, and CVE-2021-26312. These
      issues are not unique to HPE servers.
      
      Addressed an issue where in the OS does not display the true CPU Max Core
      Frequency.
      
      Addressed an issue with AMD EPYC 1st Generation processors that can result in
      Corrected Memory Error Threshold Events being logged to the Integrated
      Management Log (IML) in cases when they should not be logged. The system
      monitors corrected errors and notifies the user when action is required due to
      an increased risk of an Uncorrected Memory Error. Corrected Memory errors are
      a normal and expected occurrence and do not always indicate a higher risk of
      an Uncorrected Memory Error. Previous revisions of the System ROM were
      incorrectly logging Corrected Memory Error Threshold Events to the IML when
      action should not have been required, resulting in unnecessary scheduled
      downtime to replace DIMMs. It is recommended that the System ROM be updated to
      this version before replacing DIMMs due to Corrected Memory Error Threshold
      Events.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54_12-03-2021
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue that can result in Corrected Memory Error Threshold Events
      being logged to the Integrated Management Log (IML) incorrectly. The system
      monitors corrected memory errors and notifies the user via a Corrected Memory
      Error Threshold Event when action is recommended due to an increased risk of
      an uncorrected memory error. Previous versions of the System ROM may log a
      Corrected Memory Error Threshold Event in cases where the system is not at an
      increased risk of an uncorrected memory error. It is strongly recommended that
      the System ROM be updated to this version or later before replacing DIMMs due
      to Corrected Memory Error Threshold Events.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.56_02-10-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where RAID volumes will be lost when using the "Restore
      Default Manufacturing Settings" feature.
      
      Addressed an issue where if the Administrator Password and Power-On Password
      are set, after clearing the Power-On Password, Administrator Password is also
      cleared.
      
      Addressed an issue where a system with Microsoft BitLocker enabled may
      incorrectly and intermittently prompt the user to unlock drives after a
      graceful OS reboot.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.58_06-16-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigations for security vulnerabilities documented as CVE-2022-0778
      and CVE-2022-1292. These issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of LibPng library
      which provides mitigations for security vulnerability documented as CVE-
      CVE-2019-7317. This issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where the system ROM does not display Storage controller
      product names when the ROM Based Setup Utility (RBSU) language setting is non-
      English.
      
      Addressed an issue where systems using AMD 1st Generation EPYC processors
      would incorrectly count correctable DIMM errors from different channels into
      one channel thus possibly incorrectly causing Correctable Memory Error
      Threshold Exceeded errors to occur.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60_08-11-2022
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code 100E for AMD 2nd Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 2nd Generation EPYC processors.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigations for security vulnerabilities documented as
      CVE-2022-02068. These issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerabilities documented as
      CVE-2022-27404, CVE-2022-27405, and CVE-2022-27406. This issue is not unique
      to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.64_11-17-2022
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code 100E for AMD 2nd Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 2nd Generation EPYC processors.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_02-02-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM updates zlib to 1.2.13 which provides
      mitigation for BIOS security vulnerability documented as CVE-2022-37434.
      
      (https://nvd.nist.gov/vuln/detail/CVE-2022-37434). This security vulnerability
      is documented in the CVE report site. This issue is not unique to HPE servers.
      
      Addressed an issue where some Chinese translation is missing from RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_04-20-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code RomePI 1.0.0.E for
      AMD 2nd Generation EPYC processors. This revision of the System ROM includes
      AMD reference code NaplesPI 1.0.0.J for AMD 1st Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where an abnormal MR controller name would display when
      setting the system language to Japanese from RBSU, and then rebooting the
      system.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages was not
      synchronized.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.80_07-31-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code RomePI 1.0.0.F for
      AMD 2nd Generation EPYC processors. This revision of the System ROM includes
      AMD reference code NaplesPI 1.0.0.K for AMD 1st Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision provides AMD's mitigation for security vulnerabilities for
      CVE-2022-23829 for AMD 1st Generation EPYC processors, and CVE-2022-23829 and
      CVE-2023-20593 for AMD 2nd Generation EPYC processor. This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.0.2zh update which provides mitigation for security vulnerabilities
      documented as CVE-2023-2650.
      
      Addressed an issue where iLO embedded device health info would display blank
      content under RBSU when the Language was set to Japanese or Chinese.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.58_06-09-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the AMD
      reference code for AMD 3rd Generation EPYC processors which addresses and
      issue with Windows 2022 AQ Secure Core certification.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerability documented as
      CVE-2022-0778. This security vulnerability is documented in the CVE report
      site https://nvd.nist.gov/vuln/detail/CVE-2022-0778. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigation for BIOS security vulnerability documented
      as CVE-2022-27405. This security vulnerability is documented in the CVE report
      site https://nvd.nist.gov/vuln/detail/CVE-2022-27405. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where the system fails to boot OpenShift Container Platform
      in UEFI boot and optimized boot modes.
      
      Addressed an issue where the IPMI Watchdog Timer (WDT) would continuously be
      re-enabled on reboots even after being disabled which causes the system to
      continuously reboot after the timeout is triggered.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60_08-11-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 2nd Generation EPYC processors.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerability documented as
      CVE-2022-2068 (https://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      Addressed an issue where the QR Code in ROM Based Setup Menu (RBSU) was not
      valid.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.64_11-17-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 2nd Generation EPYC processors.
      
      Addressed an issue where the system would encounter an unexpected shutdown
      with "Internal processors error" in the IML while running the TPM scripts.
      
      Addressed an issue where the system boot-up would hang if the system has
      installed mutiple PCIe devices and set to "Dual Bifurcation" at the same time.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_02-06-2023
changelog:
  -     Add new System Configuration (RBSU) configuration options that allow
      controlling the processor's P0 (maximum) frequency. This includes the "Custom
      Pstate0" option with settings of "Auto" (default) and "Manual" and the
      "Pstate0 Frequency(MHz)" option that allows setting the P0 frequency. When
      the "Custom Pstate0" option is configured for "Manual", the value of the
      "Pstate0 Frequency(MHz)" is used for the processor's P0 frequency. When the
      "Custom Pstate0" option is configured for "Auto", the processor uses its
      normal, maximum P0 frequency and the "Pstate0 Frequency(MHz)" option is not
      configurable. In System Configuration (RBSU), these options are located under
      the BIOS/Processor Options. This setting has the following Redfish
      properties:
      
      /redfish/v1/systems/1/bios/settings/CustomPstate0
      
      /redfish/v1/systems/1/bios/settings/Pstate0Frequency


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_02-06-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM updates zlib to 1.2.13 which provides
      mitigation for BIOS security vulnerability documented as CVE-2022-37434.
      
      (https://nvd.nist.gov/vuln/detail/CVE-2022-37434). This security vulnerability
      is documented in the CVE report site.
      
      This revision of the System ROM includes the v1.1.1s openSSL which provides
      mitigation for BIOS security vulnerability documented as CVE-2022-2097.
      
      (https://nvd.nist.gov/vuln/detail/CVE-2022-2097). This security vulnerability
      is documented in the CVE report site.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_04-20-2023
changelog:
  -     The following options from RBSU will hide if using customized iPXE.
      
       iPXE Script Auto-Start
      
       iPXE Script Verification
      
       iPXE Auto-Start Script Location
      
       Network Location for iPXE Auto-Start Script


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_04-20-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code RomePI 1.0.0.F for
      AMD 2nd Generation EPYC processors. This revision of the System ROM includes
      AMD reference code MilanPI 1.0.0.A for AMD 3rd Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the "Access Control Service" option under RBSU did
      not work.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.80_07-31-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code RomePI 1.0.0.F for
      AMD 2nd Generation EPYC processors. This revision of the System ROM includes
      AMD reference code MilanPI 1.0.0.B for AMD 3rd Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision provides AMD's mitigation for security vulnerabilities for
      CVE-2022-23829 and CVE-2023-20593 for AMD 2nd Generation EPYC processors, and
      CVE-2022-23829 and CVE-2023-20569 for AMD 3rd Generation EPYC processor. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for security vulnerabilities
      documented as CVE-2023-0286, CVE-2022-4304 and CVE-2023-2650.
      
      Addressed an issue where Secure Boot would not be enabled when loading
      manufacturing default from iLO web.
      
      Addressed an issue where RSOD would occur when entering "System Information"
      from RBSU under legacy mode.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_02-06-2023
changelog:
  -     Add new System Configuration (RBSU) configuration options that allow
      controlling the processors P0 (maximum) frequency. This includes the Custom
      Pstate0 option with settings of Auto (default) and Manual and the Pstate0
      Frequency(MHz) option that allows setting the P0 frequency. When the Custom
      Pstate0 option is configured for Manual, the value of the Pstate0
      Frequency(MHz) is used for the processors P0 frequency. When the Custom
      Pstate0 option is configured for Auto, the processor uses its normal, maximum
      P0 frequency and the Pstate0 Frequency(MHz) option is not configurable. In
      System Configuration (RBSU), these options are located under the
      BIOS/Processor Options. This setting has the following Redfish properties:
      
      /redfish/v1/systems/1/bios/settings/CustomPstate0
      
      /redfish/v1/systems/1/bios/settings/Pstate0Frequency


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_04-20-2023
changelog:
  -     The following options from RBSU will hide if using customized iPXE.
      
      iPXE Script Auto-Start
      
      iPXE Script Verification
      
      iPXE Auto-Start Script Location
      
      Network Location for iPXE Auto-Start Script


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.80_07-31-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code RomePI 1.0.0.F for
      AMD 2nd Generation EPYC processors. This revision of the System ROM includes
      AMD reference code MilanPI 1.0.0.B for AMD 3rd Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision provides AMD's mitigation for security vulnerabilities for
      CVE-2022-23829 and CVE-2023-20593 for AMD 2nd Generation EPYC processors, and
      CVE-2022-23829 and CVE-2023-20569 for AMD 3rd Generation EPYC processor. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for security vulnerabilities
      documented as CVE-2023-0286, CVE-2022-4304 and CVE-2023-2650.
      
      Addressed an issue where Secure Boot would not be enabled when loading
      manufacturing default from iLO web.
      
      Addressed an issue where RSOD would occur when entering System Information
      from RBSU under legacy mode.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.58_06-09-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the AMD
      reference code for AMD 3rd Generation EPYC processors which addresses and
      issue with Windows 2022 AQ Secure Core certification.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerability documented as
      CVE-2022-0778. This security vulnerability is documented in the CVE report
      site. This issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigation for BIOS security vulnerability documented
      as CVE-2022-27405. This security vulnerability is documented in the CVE report
      site. This issue is not unique to HPE servers.
      
      https://nvd.nist.gov/vuln/detail/CVE-2022-27405
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where the system fails to boot OpenShift Container Platform
      in UEFI boot and optimized boot modes.
      
      Addressed an issue where the IPMI Watchdog Timer (WDT) would continuously be
      re-enabled on reboots even after being disabled which causes the system to
      continuously reboot after the timeout is triggered.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.66_05-17-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of openSSL and
      LibPng which provides mitigation for BIOS security vulnerabilities documented
      as CVE-2022-1292 and CVE-2019-7317. This security vulnerability is documented
      in the CVE report site. This issue is not unique to HPE servers.
      
      Addressed an issue of an incomplete mitigation for a BIOS advisory and
      security vulnerabilities documented as CVE-2021-0159, CVE-2021-33123, and
      CVE-2021-33124. These security vulnerabilities are documented in Intel
      Security Advisory INTEL-SA-00601. These issues are not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_07-14-2022
changelog:
  -     Added support for One Button Secure Erase (OBSE) and encryption for Broadcom
      MR controller series on Intel Gen10 systems.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_07-14-2022
changelog:
  -     *Important Notes:**
      
      When installing with HPE Smart Update Manager (SUM) 8.9.5 or earlier, the
      warning message "Component Not Signed" might be displayed for SHA-384 signed
      components. This issue will be resolved in a future version of SUM. For
      details, see https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&d
      ocId=a00125612en_us.
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerability documented as
      CVE-2022-2068 (ttps://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerabilities documented as
      CVE-2022-27404, CVE-2022-27405, and CVE-2022-27406. This issue is not unique
      to HPE servers.
      
      Addressed an issue where the system will hang with Red Screen of Death (RSOD)
      in ROM Based Setup Utility (RBSU) when user tries to switch [Image
      Description] choices for NVMe devices under the Firmware Update Page.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_09-29-2022
changelog:
  -     Updated Intel Optane Memory UEFI driver.
      
      Added support to show manufacturing date for DIMMs in SMBIOS.
      
      Improved the description of Memory Failed Events in the Integrated Management
      Log (IML).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_09-29-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where a server running the ESXi hypervisor a with TPM
      module installed would halt on loading modules after the installation of the
      hypervisor OS, with the message "TPM log extend failed".
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.76_02-09-2023
changelog:
  -     Added new System Configuration (RBSU) configuration options that allow
      enabling and disabling EPP (Energy Performance Preference) when "Workload
      Profile" sets to "Custom" and "Power Regulator" sets to "OS Control Mode".


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.76_02-09-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.1 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-32231 and CVE-2022-26343. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the zlib library
      1.2.13 update which provides mitigation for and security vulnerabilities
      documented as CVE-2022-37434. This issue is not unique to HPE servers.
      
      Addressed an issue that system will hang when BIOS tries to print a large IML
      message on POST screen.
      
      Addressed an issue when system discovers thousands of LUNs and was trying to
      create thousands of boot options for each LUNs. System cannot add, delete or
      adjust new boot options on iLO web and RBSU after rebooting. System becomes
      unstable unless loading manufacture default.
      
      Addressed an issue where some Chinese and Japanese translations were missing
      in RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.78_03-16-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where servers may stop responding during boot when the
      Intel TXT function is enabled.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.80_04-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.2 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-38087. This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      Addressed the issue where the system might hang due to invalid memory free and
      usage when TPM is enabled.
      
      Addressed the issue where the PCIe device serial number in OEM SMBIOS type 203
      does not populate in some cases.
      
      Addressed the issue where the power-on-password dialog popped up even though
      user did not set the password.
      
      Addressed the issue where the TPM status between RBSU and iLO web pages was
      not synchronized.
      
      Addressed the issue where BIOS does not correctly log memory error data and
      memory health telemetry in AHS.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.90_07-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-43505 and CVE-2022-40982. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.0.2zh update which provides mitigation for security vulnerabilities
      documented as CVE-2023-2650.
      
      Addressed an issue where iLO embedded device health info would display blank
      content under RBSU when the Language was set to Japanese or Chinese.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_07-14-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerability documented as
      CVE-2022-2068 (ttps://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerabilities documented as
      CVE-2022-27404, CVE-2022-27405, and CVE-2022-27406. This issue is not unique
      to HPE servers.
      
      Addressed an issue where the system will hang with Red Screen of Death (RSOD)
      in ROM Based Setup Utility (RBSU) when user tries to switch [Image
      Description] choices for NVMe devices under the Firmware Update Page.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.90_07-20-2023
changelog:
  -     This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-43505 and CVE-2022-40982. This
      security vulnerability is documented in the CVE report site.  This issue is
      not unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.0.2zh update which provides mitigation for security vulnerabilities
      documented as CVE-2023-2650.
      
      Addressed an issue where iLO embedded device health info would display blank
      content under RBSU when the Language was set to Japanese or Chinese.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.69_08-19-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Enhanced the system thermal settings to provide improved acoustics when the
      server is configured in legacy boot mode with M.2 SSDs.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.52_09-16-2021
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2021.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where High Precision Event Timer in Windows was not showing
      up in device manager.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54_10-21-2021
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2021.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2021.2 which provides mitigations for BIOS advisories and security
      vulnerabilities documented as CVE-2021-0157. These security vulnerabilities
      are documented in the CVE report site. This issue is not unique to HPE
      servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.56_01-20-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2021.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes Intel Platform Update 2021.2 which
      provides mitigations for security vulnerabilities CVE-2021-0092,
      CVE-2021-0127, CVE-2021-0156 and CVE-2021-0157. These issues are not unique to
      HPE servers.
      
      Fixed an issue where system boot mode changed to Legacy mode from UEFI mode
      after IP flash complete and system may hang when entering IP after setting to
      UEFI mode.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.58_04-14-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel
      microcode which provides mitigations for security vulnerability documented as
      CVE-2022-21166, CVE-2022-21125, CVE-2022-21123, CVE-2022-21127,
      CVE-2022-21151, and CVE-2022-0005. These security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00617 and INTEL-SA-00614. These
      issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerabilities documented as CVE-2021-0154, CVE-2021-0189, CVE-2021-33123,
      CVE-2021-33124, and CVE-2021-33159. These security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00601 and INTEL-SA-00610. These
      issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where the server may become unresponsive during POST with
      error messages about Unknown Initialization Error and DIMM Initialization
      Error. For more details please read the below advisory:
      https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60_07-14-2022
changelog:
  -     *Important Notes:**
      
      When installing with HPE Smart Update Manager (SUM) 8.9.5 or earlier, the
      warning message "Component Not Signed" might be displayed for SHA-384 signed
      components. This issue will be resolved in a future version of SUM. For
      details, see https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&d
      ocId=a00125612en_us.
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerabilities documented as
      CVE-2022-0778 (https://nvd.nist.gov/vuln/detail/CVE-2022-0778 ), CVE-2022-1292
      (https://nvd.nist.gov/vuln/detail/CVE-2022-2068 ) and CVE-2022-2068
      (https://nvd.nist.gov/vuln/detail/CVE-2022-1292). This security vulnerability
      is documented in the CVE report site. This issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerabilities documented as
      CVE-2022-27404, CVE-2022-27405, and CVE-2022-27406. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of Libpng library
      which provides mitigations for security vulnerability documented as
      CVE-2019-7317 (https://nvd.nist.gov/vuln/detail/CVE-2019-7317). This issue is
      not unique to HPE servers.
      
      Removed PCIe bifurcation option in the ROM Based Setup Utility (RBSU) because
      it is not supported through ROM on this platform.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.64_10-13-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-26837. This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      Addressed an issue where firmware BootTimer would cause a black screen hang
      when switching TPM 1.2 to 2.0.
      
      Addressed an issue TPM Visibility option in ROM Based Setup Utility (RBSU)
      would be greyed out after upgrading the system ROM from 2.54 to 2.58.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.68_01-12-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.1 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-33894 and CVE-2022-26837. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the zlib library
      1.2.13 update which provides mitigation for security vulnerabilities
      documented as CVE-2022-37434.
      
      Addressed an issue that system will hang when BIOS tries to print a large IML
      message on POST screen.
      
      Addressed an issue when system discovers thousands of LUNs and was trying to
      create thousands of boot options for each LUN. System cannot add, delete or
      adjust new boot options on iLO web and RBSU after rebooting. System becomes
      unstable unless loading manufacture defaults.
      
      Addressed an issue where some Chinese and Japaneses translations were missing
      from RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72_04-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.2 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-33894 and CVE-2022-38087. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      Addressed an issue where the PCIe device serial number in OEM SMBIOS type 203
      does not populate in some cases.
      
      Addressed an issue where the power-on-password dialog popped up even though
      user did not set a password.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages was not
      synchronized.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.80_07-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-44611 and CVE-2022-40982. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.0.2zh update which provides mitigation for security vulnerabilities
      documented as CVE-2023-2650.
      
      Addressed an issue where iLO embedded device health info would display blank
      content under RBSU when the Language was set to Japanese or Chinese.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.58_04-14-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel
      microcode which provides mitigations for security vulnerability documented as
      CVE-2022-21166, CVE-2022-21125, CVE-2022-21123, CVE-2022-21127,
      CVE-2022-21151, and CVE-2022-0005. These security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00617 and INTEL-SA-00614. These
      issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerabilities documented as CVE-2021-0154, CVE-2021-0189, CVE-2021-33123,
      CVE-2021-33124, and CVE-2021-33159. These security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00601 and INTEL-SA-00610. These
      issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where the system ROM does not display Storage controller
      product names when the ROM Based Setup Utility (RBSU) language setting is non-
      English.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_06-01-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel
      microcode which provides mitigations for security vulnerability documented as
      CVE-2022-21166, CVE-2022-21136, and CVE-2022-21151. These security
      vulnerabilities are documented in Intel Security Advisory INTEL-SA-00616, and
      INTEL-SA-00617. These issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerabilities documented as CVE-2022-0004. These security vulnerabilities
      are documented in Intel Security Advisory INTEL-SA-00613. These issues are not
      unique to HPE servers
      
      This revision of the System ROM includes the latest revision of openSSL and
      LibPng which provides mitigation for BIOS security vulnerabilities documented
      as CVE-2022-1292 and CVE-2019-7317. This security vulnerability is documented
      in the CVE report site. This issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where in the ROM Based Setup Utility (RBSU), PMem QoS
      Options cannot be set as disabled under Performance Options work profile with
      system ROM v1.58.
      
      Addressed an issue where the system fails to boot OpenShift Container Platform
      in UEFI boot and optimized boot modes.
      
      Addressed an issue where incorrect Drive Location is reported for HPE MegaRAID
      Gen10 Plus Storage Controllers under Secure Erase Report
      
      Addressed an issue where PCI network boot option shows only one port for Intel
      E810-2CQDA2 Ethernet 100Gb 2-port QSFP28 Adapter for HPE (P41611-B21) when
      bifurcation is enabled. More details can be found in the Customer Advisory
      (CA) link below: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-
      a00118261en_us
      
      Addressed an issue where the system ROM does not display Storage controller
      product names when the RBSU language setting is non-English.
      
      Addressed an issue where the IPMI Watchdog Timer (WDT) would continuously be
      re-enabled on reboots even after being disabled which causes the system to
      continuously reboot after the timeout is triggered.
      
      Addressed an issue where Advanced Memory Protection (AMP) status displays
      Degraded A3DC on iLO web page but there is no memory failure displayed in iLO.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.62_07-14-2022
changelog:
  -     *Important Notes:**
      
      When installing with HPE Smart Update Manager (SUM) 8.9.5 or earlier, the
      warning message "Component Not Signed" might be displayed for SHA-384 signed
      components. This issue will be resolved in a future version of SUM. For
      details, see https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&d
      ocId=a00125612en_us.
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.2 microcode update which provides Intel's mitigation for BIOS advisory
      and security vulnerability documented as CVE-2022-21233. This security
      vulnerabilities are documented in Intel Security Advisory INTEL-SA-00657. This
      issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerability documented as CVE-2021-33060. This security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00686. These issues are not
      unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerabilities documented as
      CVE-2022-0778 (https://nvd.nist.gov/vuln/detail/CVE-2022-0778) and
      CVE-2022-2068 (https://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerability documented as
      CVE-2022-27405 (https://nvd.nist.gov/vuln/detail/CVE-2022-27405). This issue
      is not unique to HPE servers.
      
      Addressed an issue where Microsoft Secured-core is not grayed-out when TPM is
      not present.
      
      Addressed an issue where the QR code in Rom Based Set Up menu linked to a
      discontinued site.
      
      Addressed an issue where a hot plug event occurring before event handler
      operates would cause ESXi kernel to call exception waiting for hot plug status
      from device and then triggered an ASSERT with PSOD (Purple Screen Of Death).
      
      Addressed an issue with displaying FW versions for Intel's latest ATS-M GPU
      cards.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64_08-11-2022
changelog:
  -     *Important Notes:**
      
      For customers who had already upgraded to v1.62 7/14/2022 ROM, it is highly
      recommended to upgrade to this version v1.64 if customers have Intel Optane
      Persistent Memory 200 Series installed in their system.
      
      When installing with HPE Smart Update Manager (SUM) 8.9.5 or earlier, the
      warning message "Component Not Signed" might be displayed for SHA-384 signed
      components. This issue will be resolved in a future version of SUM. For
      details, see https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&d
      ocId=a00125612en_us.
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue from previous published ROM release v1.62 7/14/2022 in
      which systems with Intel Optane Persistent Memory 200 Series may not appear
      under an OS.
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.2 microcode update which provides Intel's mitigation for BIOS advisory
      and security vulnerability documented as CVE-2022-21233. This security
      vulnerabilities are documented in Intel Security Advisory INTEL-SA-00657. This
      issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerability documented as CVE-2021-33060. This security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00686. These issues are not
      unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerabilities documented as
      CVE-2022-0778 (https://nvd.nist.gov/vuln/detail/CVE-2022-0778) and
      CVE-2022-2068 (https://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerability documented as
      CVE-2022-27405 (https://nvd.nist.gov/vuln/detail/CVE-2022-27405). This issue
      is not unique to HPE servers.
      
      Addressed an issue where Microsoft Secured-core is not grayed-out when TPM is
      not present.
      
      Addressed an issue where the QR code in Rom Based Set Up menu linked to a
      discontinued site.
      
      Addressed an issue where a hot plug event occurring before event handler
      operates would cause ESXi kernel to call exception waiting for hot plug status
      from device and then triggered an ASSERT with PSOD (Purple Screen Of Death).
      
      Addressed an issue with displaying FW versions for Intel's latest ATS-M GPU
      cards.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.68_10-27-2022
changelog:
  -     Added support to show manufacturing date for DIMMs in SMBIOS.
      
      This revision of the System ROM includes an updated revision of Intel VROC
      UEFI driver.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.68_10-27-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel PLR3
      OOB guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel PLR3
      OOB update which provides Intel's mitigation for BIOS advisory and security
      vulnerability documented as CVE-2022-33972. This security vulnerability is
      documented in the CVE report site. This issue is not unique to HPE servers.
      
      Addressed an issue where an HPE MR controller's name is displayed abnormally
      after setting the language to Japanese in ROM Based Setup Utility (RBSU)
      rebooting the system.
      
      Addressed an issue where the Boot timer record was increasing incorrectly
      after every warm reboot.
      
      Addressed a possible hang issue when using a newer PCIe device with a very
      high PCI bus requirement.
      
      Addressed an issue where "Reboot Required" radio button isn't highlighted
      after BIOS restore.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72_02-02-2023
changelog:
  -     Added "Important: Intel(R) NVMe and Intel(R) VROC are not supported when the
      Boot Mode is configured in Legacy BIOS Mode." message into the RBSU help
      description for Intel NVMe VROC option.
      
      Added new System Configuration (RBSU) configuration options that allow
      enabling and disabling EPP (Energy Performance Preference) when "Workload
      Profile" sets to "Custom" and "Power Regulator" sets to "OS Control Mode".
      
      Downgraded several debug messages from DEBUG_ERROR to DEBUG_INFO level.
      Removed unnecessary error messages in BIOS serial log.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72_02-02-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.1 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-21216, CVE-2022-32231,
      CVE-2022-26343, CVE-2022-33196, CVE-2022-38090 and CVE-2022-33972. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the zlib library
      1.2.13 update which provides mitigation for and security vulnerabilities
      documented as CVE-2022-37434.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1s update which provides mitigation for security vulnerabilities
      documented as CVE-2022-2097.
      
      Addressed an issue where the controller name was not displayed in Japanese
      when MegaRAID was switched to Japanese, .
      
      Addressed an issue where NVMe drive info was not displayed properly in iLO
      when Intel PCH VMD is enabled in RBSU.
      
      Addressed an issue where Intel VROC SATA firmware shows N/A under PCI Device
      information.
      
      Addressed an issue when system discovers thousands of LUNs and was trying to
      create thousands of boot options for each LUNs. System cannot add, delete or
      adjust new boot options on iLO web and RBSU after rebooting. System becomes
      unstable unless loading manufacture default.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.76_04-20-2023
changelog:
  -     Added new System Configuration (RBSU) configuration options that allow user
      input frequency scaling of the processor's internal busses. In System
      Configuration (RBSU), the options is located under "Uncore Frequency Scaling"
      option in "Power and Performance Options". This setting has the following
      Redfish properties.
      
      /redfish/v1/systems/1/bios/settings/UncoreFrequencyMax
      
      /redfish/v1/systems/1/bios/settings/UncoreFrequencyMin
      
      Added new System Configuration (RBSU) configuration options that allow
      disabling Dynamic Loadline switches between EPB modes depending on the P-state
      behavior. Enable or disable the switch could affect the power and performance
      by condition. In System Configuration (RBSU), the options is located under
      "Power and Performance Options". This setting has the following Redfish
      properties.
      
      /redfish/v1/systems/1/bios/settings/DynamicLoadlineSwitch


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.76_04-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system would hang after uploading the Samsung
      1733/1735 U.3 NVMe Drive firmware through FMP.
      
      Addressed an issue where PMEM NUMA nodes were not continuous (3, 5) under 8 8
      isolated NUMA nodes configuration.
      
      Addressed an issue where a drive could not be unmounted when hot-plug
      interrupt was generated during the DPC recovery process, with the event going
      over the DPC threshold.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages was not
      synchronized.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.80_07-05-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-43505, CVE-2022-40982,
      CVE-2023-23908 and CVE-2022-41804. This security vulnerability is documented
      in the CVE report site. This issue is not unique to HPE servers.
      
      Address an issue where an abnormal power-on-password dialog would pop up even
      though user did not set a password.
      
      Address the issue where the RBSU "Storage Device Information" was empty when
      VROC is enabled.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for security vulnerabilities
      documented as CVE-2023-0286, CVE-2022-4304 and CVE-2023-2650.
      
      Address the issue where the TPM status displayed in RBSU and iLO web page was
      not in sync.
      
      Address the issue where Secure Boot would not be enabled when loading
      manufacturing default from iLO web.
      
      Address an issue where RSOD would occur when entering "System Information"
      from RBSU under legacy mode.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_05-12-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel
      microcode which provides mitigations for security vulnerability documented as
      CVE-2022-21166, CVE-2022-21136, and CVE-2022-21151. These security
      vulnerabilities are documented in Intel Security Advisory INTEL-SA-00616, and
      INTEL-SA-00617. These issues are not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerabilities documented as CVE-2022-0004. These security vulnerabilities
      are documented in Intel Security Advisory INTEL-SA-00613. These issues are not
      unique to HPE servers
      
      This revision of the System ROM includes the latest revision of openSSL and
      LibPng which provides mitigation for BIOS security vulnerabilities documented
      as CVE-2022-1292 and CVE-2019-7317. This security vulnerability is documented
      in the CVE report site. This issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where in the ROM Based Setup Utility (RBSU), PMem QoS
      Options cannot be set as disabled under Performance Options work profile with
      system ROM v1.58.
      
      Addressed an issue where the system fails to boot OpenShift Container Platform
      in UEFI boot and optimized boot modes.
      
      Addressed an issue where incorrect Drive Location is reported for HPE MegaRAID
      Gen10 Plus Storage Controllers under Secure Erase Report
      
      Addressed an issue where PCI network boot option shows only one port for Intel
      E810-2CQDA2 Ethernet 100Gb 2-port QSFP28 Adapter for HPE (P41611-B21) when
      bifurcation is enabled. More details can be found in the Customer Advisory
      (CA) link below
      
      https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00118261en_us
      
      Addressed an issue where the system ROM does not display Storage controller
      product names when the RBSU language setting is non-English.
      
      Addressed an issue where the IPMI Watchdog Timer (WDT) would continuously be
      re-enabled on reboots even after being disabled which causes the system to
      continuously reboot after the timeout is triggered.
      
      Addressed an issue where Advanced Memory Protection (AMP) status displays
      Degraded A3DC on iLO web page but there is no memory failure displayed in iLO.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.62_07-14-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.2 microcode update which provides Intel's mitigation for BIOS advisory
      and security vulnerability documented as CVE-2022-21233. This security
      vulnerabilities are documented in Intel Security Advisory INTEL-SA-00657. This
      issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerability documented as CVE-2021-33060. This security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00686. These issues are not
      unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerabilities documented as
      CVE-2022-0778 (https://nvd.nist.gov/vuln/detail/CVE-2022-0778) and
      CVE-2022-2068 (https://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerability documented as
      CVE-2022-27405 (https://nvd.nist.gov/vuln/detail/CVE-2022-27405). This issue
      is not unique to HPE servers.
      
      Addressed an issue where Microsoft Secured-core is not grayed-out when TPM is
      not present.
      
      Addressed an issue where the QR code in Rom Based Set Up menu linked to a
      discontinued site.
      
      Addressed an issue where a hot plug event occurring before event handler
      operates would cause ESXi kernel to call exception waiting for hot plug status
      from device and then triggered an ASSERT with PSOD (Purple Screen Of Death).
      
      Addressed an issue with displaying FW versions for Intel's latest ATS-M GPU
      cards.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64_08-11-2022
changelog:
  -     *Important Notes:**
      
      For customers who had already upgraded to v1.62 7/14/2022 ROM, it is highly
      recommended to upgrade to this version v1.64 if customers have Intel Optane
      Persistent Memory 200 Series installed in their system.
      
      When installing with HPE Smart Update Manager (SUM) 8.9.5 or earlier, the
      warning message "Component Not Signed" might be displayed for SHA-384 signed
      components. This issue will be resolved in a future version of SUM. For
      details, see https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue from previous published ROM release v1.62 7/14/2022 in
      which systems with Intel Optane Persistent Memory 200 Series may not appear
      under an OS.
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.2 microcode update which provides Intel's mitigation for BIOS advisory
      and security vulnerability documented as CVE-2022-21233. This security
      vulnerabilities are documented in Intel Security Advisory INTEL-SA-00657. This
      issue is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of the Intel
      Reference Code which provides mitigations for BIOS advisories and security
      vulnerability documented as CVE-2021-33060. This security vulnerabilities are
      documented in Intel Security Advisory INTEL-SA-00686. These issues are not
      unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerabilities documented as
      CVE-2022-0778 (https://nvd.nist.gov/vuln/detail/CVE-2022-0778) and
      CVE-2022-2068 (https://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of FreeType
      library which provides mitigations for security vulnerability documented as
      CVE-2022-27405 (https://nvd.nist.gov/vuln/detail/CVE-2022-27405). This issue
      is not unique to HPE servers.
      
      Addressed an issue where Microsoft Secured-core is not grayed-out when TPM is
      not present.
      
      Addressed an issue where the QR code in Rom Based Set Up menu linked to a
      discontinued site.
      
      Addressed an issue where a hot plug event occurring before event handler
      operates would cause ESXi kernel to call exception waiting for hot plug status
      from device and then triggered an ASSERT with PSOD (Purple Screen Of Death).
      
      Addressed an issue with displaying FW versions for Intel's latest ATS-M GPU
      cards.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.68_10-27-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel PLR3
      OOB guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel PLR3
      OOB update which provides Intel's mitigation for BIOS advisory and security
      vulnerability documented as CVE-2022-33972. This security vulnerability is
      documented in the CVE report site. This issue is not unique to HPE servers.
      
      Addressed an issue where an HPE MR controller's name is displayed abnormally
      after setting the language to Japanese in ROM Based Setup Utility (RBSU)
      rebooting the system.
      
      Addressed an issue where the Boot timer record was increasing incorrectly
      after every warm reboot.
      
      Addressed a possible hang issue when using a newer PCIe device with a very
      high PCI bus requirement.
      
      Addressed an issue where Reboot Required radio button isn't highlighted after
      BIOS restore.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72_02-02-2023
changelog:
  -     Added "Important: Intel(R) NVMe and Intel(R) VROC are not supported when the
      Boot Mode is configured in Legacy BIOS Mode." message into the RBSU help
      description for Intel NVMe VROC option.
      
      Added new System Configuration (RBSU) configuration options that allow
      enabling and disabling EPP (Energy Performance Preference) when Workload
      Profile sets to Custom and Power Regulator sets to OS Control Mode.
      
      Downgraded several debug messages from DEBUG_ERROR to DEBUG_INFO level.
      Removed unnecessary error messages in BIOS serial log.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.76_04-20-2023
changelog:
  -     Added new System Configuration (RBSU) configuration options that allow user
      input frequency scaling of the processor's internal busses. In System
      Configuration (RBSU), the options is located under Uncore Frequency Scaling
      option in Power and Performance Options. This setting has the following
      Redfish properties.
      
      /redfish/v1/systems/1/bios/settings/UncoreFrequencyMax
      
      /redfish/v1/systems/1/bios/settings/UncoreFrequencyMin
      
      Added new System Configuration (RBSU) configuration options that allow
      disabling Dynamic Loadline switches between EPB modes depending on the P-state
      behavior. Enable or disable the switch could affect the power and performance
      by condition. In System Configuration (RBSU), the options is located under
      Power and Performance Options. This setting has the following Redfish
      properties.
      
      /redfish/v1/systems/1/bios/settings/DynamicLoadlineSwitch


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.80_07-05-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-43505, CVE-2022-40982,
      CVE-2023-23908 and CVE-2022-41804. This security vulnerability is documented
      in the CVE report site. This issue is not unique to HPE servers.
      
      Address an issue where an abnormal power-on-password dialog would pop up even
      though user did not set a password.
      
      Address the issue where the RBSU "Storage Device Information" was empty when
      VROC is enabled.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for security vulnerabilities
      documented as CVE-2023-0286, CVE-2022-4304 and CVE-2023-2650.
      
      Address the issue where the TPM status displayed in RBSU and iLO web page was
      not in sync.
      
      Address the issue where Secure Boot would not be enabled when loading
      manufacturing default from iLO web.
      
      Address an issue where RSOD would occur when entering System Information from
      RBSU under legacy mode.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.52_09-16-2021
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2021.1 guidance. None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where High Precision Event Timer in Windows was not showing
      up in device manager.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54_10-21-2021
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2021.2 guidance. None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2021.2 which provides mitigations for BIOS advisories and security
      vulnerabilities documented as CVE-2021-0157. These security vulnerabilities
      are documented in the CVE report site. This issue is not unique to HPE
      servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.54_01-13-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the power-on password and the administrator passwords
      were both cleared when clearing one or the other. With this fix the two
      passwords will be treated independently as intended.
      
      Removed Dynamic Power Capping Functionality option from the RBSU menu as this
      option is not supported on this platform.
      
      Removed TPM1.2 option from the RBSU menu as this option is not supported on
      this platform.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56_03-24-2022
changelog:
  -     Changed the default setting of Intel VT-d Virtualization to enabled to align
      with all other Gen10 and Gen10 Plus ProLiant servers. This will not affect the
      current setting of this option when upgrading to the v1.54 04/01/2022 System
      ROM. However, when defaults are restored on a system with the v1.54 or later
      System ROM, Intel VT-d Virtualization will be enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56_03-24-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Intel X710-DA2 Ethernet 10Gb 2-port SFP Adapter
      intermittently encounters PCIe bandwidth downgrade.
      
      Addressed an issue where Windows 2022 has a yellow bang with unknown device
      when Microsoft(R) Secured-core is enabled.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.58_04-18-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM provides Intel's mitigation for BIOS advisory
      and security vulnerability documented as CVE-2022-21151, CVE-2022-0005,
      CVE-2021-33122, CVE-2021-33123, CVE-2021-33124, and CVE-2021-33103. These
      security vulnerabilities are documented in the CVE report site. This issue is
      not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_07-14-2022
changelog:
  -     *Important Notes:**
      
      When installing with HPE Smart Update Manager (SUM) 8.9.5 or earlier, the
      warning message "Component Not Signed" might be displayed for SHA-384 signed
      components. This issue will be resolved in a future version of SUM. For
      details, see https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&d
      ocId=a00125612en_us.
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.2 microcode update which provides Intel's mitigation for BIOS advisory
      and security vulnerability documented as CVE-2022-21233. This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of openSSL which
      provides mitigation for BIOS security vulnerabilities documented as
      CVE-2022-0778 (https://nvd.nist.gov/vuln/detail/CVE-2022-0778) and
      CVE-2022-2068 (https://nvd.nist.gov/vuln/detail/CVE-2022-2068). This security
      vulnerability is documented in the CVE report site. This issue is not unique
      to HPE servers.
      
      This revision of the System ROM includes the latest revision of freetype
      library which provides mitigations for security vulnerability documented as
      CVE-2022-27405 (https://nvd.nist.gov/vuln/detail/CVE-2022-27405). This issue
      is not unique to HPE servers.
      
      This revision of the System ROM includes the latest revision of zlib library
      which provides mitigations for security vulnerability documented as
      CVE-2018-25032. This issue is not unique to HPE servers.
      
      Addressed an issue where the system fails to boot OpenShift Container Platform
      in UEFI boot and optimized boot modes.
      
      Addressed an issue where the system ROM does not display Storage controller
      product names when the RBSU language setting is non-English.
      
      Addressed an issue where system would not reboot if reboot test was executed
      after PCIe Bifurcation.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64_10-20-2022
changelog:
  -     Added warning message Intel(R) NVMe is not supported when the Boot Mode is
      configured in Legacy BIOS Mode.
      
      This revision of the System ROM includes an updated revision of VROC UEFI
      driver.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64_10-20-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-21198 and CVE-2022-26837. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      Addressed an issue where "Reboot Required" radio button isn't highlighted
      after BIOS restore.
      
      Addressed an issue where an HPE MR controller's name is displayed abnormally
      after setting the language to Japanese in ROM Based Setup Utility (RBSU)
      rebooting the system.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.68_01-12-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.1 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.1 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-26837, CVE-2022-38090 and
      CVE-2022-30704. This security vulnerability is documented in the CVE report
      site. This issue is not unique to HPE servers.
      
      This revision of the System ROM includes the revision of the zlib library
      1.2.13 update which provides mitigation for security vulnerabilities
      documented as CVE-2022-37434.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1s update which provides mitigation for security vulnerabilities
      documented as CVE-2022-2097.
      
      Addressed an issue where RBSU PCI device information page does not display the
      Intel VROC SATA firmware firmware version correctly.
      
      Addressed an issue where NVMe drive info cannot display properly in iLO web
      when PCH VMD is enabled.
      
      Addressed an issue when system discovers thousands of LUNs and was trying to
      create thousands of boot options for each LUNs. System cannot add, delete or
      adjust new boot options on iLO web and RBSU after rebooting. System becomes
      unstable unless loading manufacture default.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72_04-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the field "DIMM Map-Out Reason" of OEM SMBIOS type
      232 would update incorrectly per DIMM status.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages were
      not synchronized.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.80_07-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-44611 and CVE-2022-40982. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for security vulnerabilities
      documented as CVE-2023-0286, CVE-2022-4304 and CVE-2023-2650.
      
      Address an issue where an abnormal power-on-password dialog would pop up even
      though user did not set a password.
      
      Address the issue where Secure Boot would not be enabled when loading
      manufacturing default from iLO web.
      
      Address an issue where RSOD would occur when entering "System Information"
      from RBSU under legacy mode.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56_04-01-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where SATA drives were intermittently missing.
      
      Addressed an issue where Windows 2022 has a yellow bang with unknown device
      when Microsoft(R) Secured-core is enabled.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64_10-20-2022
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2022.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2022.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-21198 and CVE-2022-26837. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      Addressed an issue where Reboot Required radio button isn't highlighted after
      BIOS restore.
      
      Addressed an issue where an HPE MR controller's name is displayed abnormally
      after setting the language to Japanese in ROM Based Setup Utility (RBSU)
      rebooting the system.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72_05-02-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the field DIMM Map-Out Reason of OEM SMBIOS type 232
      would update incorrectly per DIMM status.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages were
      not synchronized.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.80_07-20-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2023.3 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the Intel IPU
      2023.3 BIOS update which provides Intel's mitigation for BIOS advisory and
      security vulnerabilities documented as CVE-2022-44611 and CVE-2022-40982. This
      security vulnerability is documented in the CVE report site. This issue is not
      unique to HPE servers.
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for security vulnerabilities
      documented as CVE-2023-0286, CVE-2022-4304 and CVE-2023-2650.
      
      Address an issue where an abnormal power-on-password dialog would pop up even
      though user did not set a password.
      
      Address the issue where Secure Boot would not be enabled when loading
      manufacturing default from iLO web.
      
      Address an issue where RSOD would occur when entering System Information from
      RBSU under legacy mode.
      
      **Known Issues:**
      
      None


