v6.01 build1: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added NPIV QoS Support Introduced: v6.01 build1 Impact: HW: ISP24xx, ISP25xx OS: RHEL 6.x, SLES 11.x Protocol: FC, FCoE Defect/Enhancement: Defect Problem: 32bit pointers not converted properly on Big Endian systems Solution: Use correct value during 64bit pointer/value conversion Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Defect Problem: Loopback failure requires reset of the firmware Solution: Invoked reset after loopback failure is detected Introduced: v6.00 build18 Impact: HW: ISP25xx, ISP2031, ISP8001, ISP8021, ISP8031 OS: RHEL 5.x, RHEL 6.x, SLES 10.x, SLES 11.x Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: A log message is seen in /var/log/messages while accessing QLogic's Udev files Solution: Read Udev Rules file in read-only mode to get Udev Names of disks Introduced: v4.00 build15 Impact: HW: All adapters OS: RHEL 6.2, RHEL 6.3 Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: Some QLogic mezz adapters needs to read/write data on devices connected through I2C bus on the adapter Solution: Add I2C read/write support Introduced: v6.01 build1 Impact: HW: ISP25xx, ISP2031 OS: RHEL 5.x, RHEL 6.x, SLES 10.x, SLES 11.x Protocol: FC, FCoE Defect/Enhancement: Defect Problem: API segfaults if a faulty adapter is not completely detected Solution: Ignore adapter if partially detected. Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Add Get FW Dump Support for sysfs based drivers Introduced: v6.01 build1 Impact: HW: All adapters OS: RHEL 6.x, SLES 11.x Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Add FCE Trace Buffer support Introduced: v6.01 build1 Impact: HW: ISP25xx, ISP2031, ISP8001, ISP8031 OS: RHEL 6.x, SLES 11.x Protocol: FC, FCoE v6.01 build2: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Read Model Description from VPD for ISP2031/ISP8031 adapters Introduced: v6.01 build2 Impact: HW: ISP2031, ISP8031 OS: RHEL 5.x, RHEL 6.x, SLES 10.x, SLES 11.x Protocol: FC, FCoE Defect/Enhancement: Defect Problem: Flash read fails through vports for ISP24xx adapters Solution: Allow flash read using vport handle for ISP24xx adapters Introduced: v6.00 build1 Impact: HW: ISP24xx OS: RHEL 5.x, RHEL 6.x, SLES 10.x, SLES 11.x Protocol: FC, FCoE v6.01 build3: ------------- Defect/Enhancement: Defect Problem: "Encounterd and error loading: /usr/lib/libqlsdm.so" message seen when adapter not present or driver not loaded Solution: Return success for load library Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.01 build4: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Read Board Temperature for ISP2031/IS8031 adapters Introduced: v6.01 build4 Impact: HW: ISP2031, ISP8031 OS: All supported Linux flavors Protocol: FC, FCoE v6.01 build5: ------------- Defect/Enhancement: Defect Problem: Boot Code expansion region is not flashed during flash update Solution: Update Boot Code expnasion region Introduced: v4.00 build2 Impact: HW: ISP2532 OS: All supported Linux flavors Protocol: FC v6.02 build1: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added ISP8044 support Introduced: v6.02 build1 Impact: HW: ISP8044 OS: All supported Linux flavors Protocol: FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Added EP2831 support Introduced: v6.02 build1 Impact: HW: EP2831 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Added EP8831 support Introduced: v6.02 build1 Impact: HW: EP8831 OS: All supported Linux flavors Protocol: FCoE v6.02 build2: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Update Flash versions without reset after flash update Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Retry flash operations after a delay when driver returns BUSY Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Send only Report LUNs command on first LUN found Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.02 build3: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add SerDes Register read/write support Introduced: v6.02 build3 Impact: HW: ISP2031 OS: All supported Linux flavors Protocol: FC v6.02 build4: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add 32bit SerDes Register read/write support Introduced: v6.02 build4 Impact: HW: ISP8044 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Allow FCoE context reset for ISP8044 after NVRAM update Introduced: v6.02 build4 Impact: HW: ISP8044 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Defect Problem: Targets are not visible if Lun 0 is not present Solution: Find first valid LUN found and send SCSI comands on it Introduced: v6.02 build2 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.02 build7: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add ECHO ELS support Introduced: v6.02 build7 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Defect Problem: Additional data sent in get statistics Solution: Removed invalid code from get statistics Introduced: v6.00 build2 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.02 build9: ------------- Defect/Enhancement: Defect Problem: Get statistics failing on RHEL5/SLES10 Solution: Use min data size for statistics required by driver Introduced: v6.00 build7 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.02 build12: ------------- Defect/Enhancement: Defect Problem: CT Ping failing in ESXi 5.0/5.1 Solution: Corrected code to get valid topology Introduced: v6.00 build10 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.02 build11: ------------- Defect/Enhancement: Defect Problem: Lun persistent names failing on RHEL7 Solution: Use ATTR(S){} or SYSFS{} in udev rules based on udev version Introduced: v5.00 build6 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.02 build10: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add D-Port Diagnosic info support Introduced: v6.02 build10 Impact: HW: ISP2031, ISP8031 OS: All supported Linux flavors Protocol: FC, FCoE v6.02 build13: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add Fabric Priority support for ESXi Introduced: v6.02 build13 Impact: HW: ISP2031, ISP8031 OS: VMware ESXi 5.1 Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Add supported list of adapters in Provides section Introduced: N/A Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.03 build1: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added ISP2071 and ISP2271 support Introduced: v6.03 build1 Impact: HW: ISP2071 and ISP2271 based adapters OS: All supported Linux flavors Protocol: FC v6.03 build3: ------------- Defect/Enhancement: Defect Problem: HBA_GetFcpTargetMapping fails for LUN number > 256 Solution: Honor LUN addressing method while reading LUN numbers for HBA_GetFcpTargetMapping API with LUN numbers > 256 Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Defect Problem: HBA_SendScsiInquiry and HBA_SendReadCapacity fails for LUN number > 256 Solution: Use SAM-2 LUN addressing for HBA_SendScsiInquiry and HBA_SendReadCapacity SNIA APIs for LUN numbers > 256 Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.03 build10: ------------- Defect/Enhancement: Defect Problem: Access denied messages seen on VMware ESXi 5.1 Solution: Block get shared database count API for ESXi Introduced: Day One Impact: HW: All adapters OS: VMware ESXi 5.1 Protocol: FC, FCoE Defect/Enhancement: Defect Problem: SDGetQoS API succeeds even if QoS region is not present in the flash Solution: Add QoS region check in SDGetQoS API Introduced: v6.02 build13 Impact: HW: ISP2031, ISP8031, ISP2071, ISP2271 OS: VMware ESXi 5.1 Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Added ISP2261 support Introduced: v6.03 build10 Impact: HW: ISP2261 based adapters OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Add MPI and PEP versions for 27xx adapters Introduced: v6.03 build10 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build3: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add ppc64le (64-bit little endian PowerPC) API support Introduced: N/A Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Add Online Flash update support Introduced: v6.04 build1 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Add Smart SAN API support Introduced: v6.04 build2 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Defect Problem: Flash update fails if online flash update feature is disabled or not supported by QLogic applications Solution: Allow flash update if online flash update feature is disabled or not supported by QLogic applications Introduced: v6.04 build1 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build8: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Return FW status in BBCR API for port down case Introduced: v6.04 build6 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build6: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add Buffer-to-Buffer Credit Recovery API support Introduced: v6.04 build6 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Add Private Statistics API support Introduced: v6.04 build6 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Defect Problem: Multiple application may do flash update simultaneously for 27xx adapters Solution: Use serial number based file for 27xx flash update token Introduced: v6.04 build1 Impact: HW: ISP2071, ISP2271, ISP2261 OS: VMware ESXi 5.1 Protocol: FC v6.04 build5: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Read FW attributes at API initialization Introduced: v6.04 build5 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.04 build4: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Validate Capabilities and Outage duration before FW activation Introduced: v6.04 build4 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build12: ------------- Defect/Enhancement: Defect Problem: timeout value is not properly converted from seconds into milliseconds Solution: Avoid converting timeout value twice into CPQFC_SendScsiCommandEx API Introduced: v6.04 build12 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.04 build11: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add CPQFC_SendScsiCommandEx API support Introduced: v6.04 build11 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.04 build10: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add DPort Diagnostics support Introduced: v6.04 build10 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Add Extended Private Statistics API support Introduced: v6.04 build10 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC, FCoE Defect/Enhancement: Enhancement Problem: N/A Solution: Add Linux ARM (Euler) support Introduced: v6.04 build10 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.04 build9: ------------- Defect/Enhancement: Defect Problem: Flash MPI and PEP version are seen out-of-sync Solution: Read flash MPI and PEP verions from primary set Introduced: v6.04 build1 Impact: HW: ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build39: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added ISP2081, ISP2281, ISP2089 and ISP2289 support Introduced: v6.04 build1 Impact: HW: ISP2081. ISP2281, ISP2089 and ISP2289 based adapters OS: All supported Linux flavors Protocol: FC v6.04 build40: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Read flash MPI and PEP versions from active image set Introduced: v6.04 build40 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build41: ------------- Defect/Enhancement: Defect Problem: BSG interface fails if /tmp is mounted with tmpfs on shared memory Solution: Use /var/cache/sdmapi for BSG device creation Introduced: v6.04 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC, FCoE v6.04 build45: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add NVRAM parameter to select FCP or NVME targets Introduced: v6.04 build45 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build44: ------------- Defect/Enhancement: Defect Problem: Apps issues seen with NVME target in RHEL Solution: Detect NVME target/luns by traversing sysfs tree Introduced: v6.04 build42 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build43: ------------- Defect/Enhancement: Defect Problem: Apps issues seen with NVME target in NPIV configuration Solution: Set deafult value of NVME targets for NPIV ports Introduced: v6.04 build42 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build42: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Add NVME target support for QLogic/Marvell Apps Introduced: v6.04 build42 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build47: ------------- Defect/Enhancement: Defect Problem: Apps initialization delay seen with NPIV ports Solution: Allow reading active flash regions for NPIV ports Introduced: v6.04 build39 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build46: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Restrict application features for NVME targets Introduced: v6.04 build45 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build48: ------------- Defect/Enhancement: Defect Problem: NVME targets not seen when NVME Id and Subsys Id are different Solution: Identify NVME targets using subsys Id Introduced: v6.04 build42 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build49: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Allow SDGetActiveRegions API for 27xx based adapters Introduced: v6.04 build45 Impact: HW: ISP2071, ISP2271, ISP2261, ISP2871, ISP2971, ISP2A61 OS: All supported Linux flavors Protocol: FC - ENHANCEMENTS - Fix new version from 3.0-2 to 3.0-3 - Added support for Brocade HBAs (Severity: Medium) - Added support for getting WWN from MSA2xxx devices in scsi_info - Fixed QLogic port state output on RHEL 5.3 - Fixed discovery of HBAs in adapter_info on Integrity servers with multiple PCI busses - Initial release with Emulex CNA support - Fix for dependency check error seen when installing with HPSUM - Removed installation check for kernel 2.6 and addded Installation check for Rhel5.3 and SLES10 SP3 onwards - Corrected Link state display information for Qlogic Adapters - Added MSA G3 support in Scsi_info.h -Perl dependancy fix for RHEL8 -Initial support added for E4 and will get updated subsequently -Fixed adpater_info code to display correct Vendor name instead of Unknown -Removed Brocade HBAs support - ENHANCEMENTS - ENHANCEMENTS - Intial release. - FIXES - Fixed an issue to align hp-health status messages. - Fixed an issue to stop pagination of IMLs when in script mode. - The "hp-snmp-agents"and "hp-health" initialization scripts are enhanced to check for the existence of a support IPMI stack. - ENHANCEMENTS - Added support for HP ProLiant G6 servers. - ASR time-out value can be set from hpasmcli when ASR is enabled. - Updated the installation instructions in hp_mgmgt_install man page. - Removed the script dependency between the hp-health and hp-snmp-agents RPM. To enable just storage agents, customers now in stall the hp-health and hp-snmp-agents. If the "/etc/init.d/hp-health" file is removed or renamed, the storage agents will start if configured in the /opt/hp/hp-snmp-agents/cma.conf file. - Init scripts .status. function for hp-snmp-agents & hp-health now differentiates whether an agent exited normally or abnorm ally. - libcpqci moved to hp-health to simplify dependency handling. and .libcpqci updated to version 2, will now handle hpilo driv er. - Added Trusted Platform Module (TPM) awareness. - FIXES - Fixed an issue where hpasmcli does segmentation fault if we execute the following sequence of commands in hpasmcli on Int el platforms: show dimm, show temp, show dimm. - Fixed the improper functioning of .repair. option in hpasmcli utility. - Fixed an issue where hpasmxld/hpasmlited was logging all the messages into syslog with priority .error.. Now it will log e ach message with its actual priority. - Fixed an issue where IML was not showing new events in hpasmlited + OpenIPMI configuration. - Fixed an issue where the command .service hp-health restart. was showing the twice. - ENHANCEMENTS - Add support for HP ProLiant DL160 G6 Server, HP ProLiant DL180 G6 Server, and HP ProLiant ML150 G6 Server. - FIXES - Fixed an issue where running multiple instances of .hplog -i' may cause more than 90% CPU utilization. - Fixed an issue where the servers with large amount of memory may ASR during memory initialization. - Fixed an issue where the hpasmlited was not notifying the agents of memory events on HP ProLiant G6 servers. - ENHANCEMENTS - Enhanced the hp-health init script to identify the multi-chassis ProLiant 100 series servers. - FIXES - Fixed the hpasmcli -s .show dimm. command to prevent isolated occurrences of segmentation fault. - ENHANCEMENTS - hpasmlited now supports long IML messages. - Added "show powermeter" command in hpasmcli. It shows the aggregate power consumption of the server. - FIXES - Fixed the following issues: 1.hpasmcli -s "show server" command showed the L2 and L3 cache information incorrectly on multi processor systems. 2.hpasmcli showed incorrect fan numbers on HP ProLiant G6 servers. 3.hpasmxld segmentation fault when the HP Integrated Lights Out 2 (iLO 2) broadcast storm occurs. - FIXES - Fixed hp-health daemon to prevent soft lockups from occurring when the HP Integrated Lights-Out (iLO) controller becomes un responsive due to network storm. - FIXES - Fixed a problem where if ambient temperature is very low, hpasmlited can incorrectly determine the system is over a tempera ture threshold and improperly shut the system down. - ENHANCEMENTS - Added support for Integrated Lights-Out 3 (iLO 3). - Added 'SHOW SEL' option in hpasmcli to display the System Event Log (SEL) contents on HP ProLiant 100 series servers. - Updated libcpqci.so, which take advantage of upstream changes to hpilo, to provide better performance to applications, such as SNMP agents like cmasm2d from hp-snmp-agents. - Added 64-bit hpbootcfg utility. - FIXES - The Intel processor hyperthreading configuration can be enabled and disabled using hpasmcli on HP ProLiant G6 servers. - Fix POSIX-compliancy issue with initscript. - Avoid sending a SIGKILL to the health daemon, preventing ASRs that may occur on platforms (e.g. DL785) where hp-health shu tdowns may take an extended amount of time. - ENHANCEMENTS - Split Advanced Server Recovery functionality into standalone hp-asrd service. For more information, execute 'man hp-asrd'. - ENHNCEMENTS - Prevent logging of the debug messages to the console. - ENHANCEMENTS - Initial release to support Red Hat Enterprise Linux 5 Update 6. - ENHANCEMENTS - hpasm interface redesigned to use sockets in order to remove timeout related issues caused by message queue interface when the system is in stress. - ENHANCEMENTS - Added support for HP ProLiant Gen9 Servers. - FIXES - HP Health may skip few lengthy POST error messages due to limitation of IPMI packet. - ENHANCEMENTS - FIXES - iLO hpasmlited daemon crash after 2 iLO resets loops. - hpasmcli command fails to read the embedded NIC status shows as UNKNOWN. - Error logs seen in service hp-asrd status. - 8.4.0 release (Severity: Medium) - ENHANCEMENTS - Added support for Integrated Lights-Out 3 (iLO 3) - ENHANCEMENTS - Added support for HP ProLiant Gen9 Servers. - FIXES - When SNMP community string is configured as other than public in snmpd.conf file, all the webapp data is now populating in HP System Management Homepage (SMH) for Red Hat Enterprise Linux (RHEL) 6.5. - ENHANCEMENTS - FIXES - ENHANCEMENTS - Initial release. - NIC Agent now shows IPV6 address in System Management Homepage (hpsmh) on IPv6 only system. - Added fan module number to message logged to syslog for MSA70. - Changed "opt/compaq" to "opt/hp/hp-snmp-agents". - Updated reported MIB revisions for 8.10 storage agents. - Make physical drive path status in the physical drive table report as PATH_STATUS_OTHER if the physical drive status is PHY S_FAILED. - Make the path table report path status as "PATH_STATUS_OTHER" when the physical drive status is unknown. - FIXES - Fixed the ProLiant Management Command Line Interface Utility (hpasmcli) to display the temperature and fan failure informat ion correctly. - Fixed the ProLiant Integrated Management Log (IML) Utility (hplog) to display number of events correctly. - Fixed the discrepancy in ASR time-out value displayed on hpasmcli and hplog. - Fixed an issue where hpasmcli, hplog and System Management Homepage (hpsmh) were showing different status for CPU fan redun dancy in HP ML350 G5. - Fixed an issue where Power supply status of HP DL585G1 not shown correctly in CLI utilities. - Fixed the hpasmcli to display the UID information correctly on HP ML310 G4. - NIC Agent now shows proper link status for Loopback interface (lo). - Fixed NIC Agent where it does not generate netsnmp_assert error messages in cma.log file. - Fixed NIC Agent to show the correct speed (10Gbps) in the System Management Homepage for 10Gig NICs. - Fixed NIC Agent to show the correct Adapter Name for HP NC380T Adapter. - Fixed issue where some events may not reported if a large number of physical drives were present. - Fixed issue where the device node name was sometimes not reported correctly for Smart array attached drives. - Fixed issue where Logical drives shown as none in hpsmh after deleting the first logical drive. - Fixed ps/grep race in storage agent (cmastor) startup script. - Fixed status of processor SCSI ID reported as unknown. - Fixed hpsmh where sometimes shows drive is blinking when it isn't. - Fixed re-insertion of hot-plugged fan module generated IPMI failure event. - Fixed an issue where cmapeerd was showing the error message "recvfrom() failed". - FIXES - Fixed the rebuild script for hp-snmp-agents. - Fixed an issue where the agents show IOCTL ERROR mddessage when it polls the first time after booting the system. - Fixed memory leak issues in presence of bond and VLan interfaces. - Fixed an issue where the agents were showing disabled on systems that don't support hyperthreading. - The hp-snmp-agents script will now properly halt if the hp-health initialization script fails to exit cleanly. - ENHANCEMENTS - Added support for HP ProLiant G6 servers. - Added Trusted Platform Module (TPM) awareness. - Removed the script dependency between the hp-health and hp-snmp-agents RPM. To enable just storage agents, customers now in stall the hp-health and hp-snmp-agents. If the "/etc/init.d/hp-health" file is removed or renamed, the storage agents will st art if configured in the /opt/hp/hp-snmp-agents/cma.conf file. - Enabled the selective bubbling up of events in Integrated Management Log. - Init scripts .status. function for hp-snmp-agents & hp-health now differentiates whether an agent exited normally or abnorm ally. - Added support for CpqHeResMem2 MIBs. - The following MIB tables have been deprecated. These tables will be removed in a future release: cpqSiMemModuleTable, cpqH eResMemBoardTable, cpqHeResMemModuleTable. The data in these tables will be available in the new cpqHe2ResMemModuleTable & cpqHe2ResMemBoardTable MIB tables. - FIXES - Fixed an issue where the cmasm2d agent used to log the following error in cma.log after an iLO reset had been occurred: "cm asm2d[7880]: sm2_ioctl: Index mismatch 50 != 51, retrying receive". - Fixed an issue when a fan removed or failed, the overall thermal and fan status will be updated correctly in System Managem ent Homepage. - Fixed an issue where the System Management Homepage was not displaying the file system details of a USB key after unmountin g and mounting it again. - Fixed an issue where the agents used to send the trap email twice after a restart. - The shut down notification sent by cmapeerd daemon is now acknowledged by all agents before the cmapeerd shuts down. This w ill eliminate the sporadic error messages logged by the agents during shut down. - The build number will now increment when the hp-snmp-agents rebuild. - ENHANCEMENTS - Add support for HP ProLiant DL160 G6 Server, HP ProLiant DL180 G6 Server, and HP ProLiant ML150 G6 Server. - ENHANCEMENTS - Added support for HP 6GB Serial Attached SCSI (SAS) hard drives. - Added support for Intel ICH10 SATA IDE controller. - Added support for HP NC362i Integrated Dual Port Gigabit Server Adapter. - Added support for NetXen and HP NC-Series Intel e1000e Driver to send the traps. - Added support for multi-board chassis product name and ID. - Updated cmasm2d polling cycle to reduce system workload. - Added the performance agents (cmaperfd). - FIXES - Fixed an issue where Linux event daemon reported RAID 1 inconsistency events. - Fixed an issue where cmaidad agents send bad request commands to HP P700m Smart Array controller. - Fixed an issue with inconsistent data by setting Monitor and performance data buffers to zero before issuing ioctls to HP S mart Array B110i SATA raid controller. - Fixed an issue where HP Smart Array B110i SATA raid controller was displayed twice as HP Smart Array B110i SATA raid contro ller and standard IDE controller. - Fixed an issue where incorrect PCA Part number and system ID details sent in trap email. - Fixed an issue where agent crashed when multiple VLANs are created and link up/down events are generated. - Fixed an issue with displaying HP BL p-Class rack data in the System Management HomePage. - Fixed an issue where cmahealthd sends the 6064 trap correctly when correctable memory errors are occurred. - Fixed an issue where System Management Homepage correctly displays the FB DDR3 DIMM type information. - Fixed an issue on HP ProLiant DL320 G6 server where the 6018 trap is not sent correctly when the temperature sensors are ov erheated. - Fixed the customer issue to use bond IP while sending traps if bondX is chosen as param in cma.conf. - Fixed problem with cmarackd startup. - FIXES - Fixed an issue where cmahealthd agent may terminate while polling memory on some. - ENHANCEMENTS - Added new 6069 trap upon AC Power loss. Also, the MIB cpqHeFltTolPowerSupplyErrorCondition will show the error information if the power supply supports error reporting. - The agents now retrieve the Power supply Serial number from Type 39 SMBIOS record if it is present. - The agents now display the negative temperature readings correctly if it is reported by the temperature sensors. - The cmahostd agent now updates the PowerPIC firmware version information in the cpHoFwVerTable. - Updated the SIM event severity to .informational. after the secure erase is completed. - Added support for HP NC362i Integrated Dual Port. - FIXES - The cmapeerd agent logs the error .sendto() failed. to cma.log file. - The DIMM type displayed incorrectly on HP ProLiant BL460c G5. - The cmahealthd agent sent the 6036 trap instead of 6035 trap upon fan failure. - The port numbers displayed incorrectly for HP NC532i Dual Port 10GbE Multifunction BL-c Adapter. - The Part Number displayed incorrectly. - The cmanicd crashed after creation of multiple VLAN, disconnect/connect of NIC link. - The System Id displayed incorrectly on the System Management Homepage (SMH). - The blink drive LED feature for HP Smart Array B110i SATA RAID Controller. - The embedded Broadcom SATA controller was not detected on System Management Homepage (SMH). - The multipath status was displayed as "unknown" when a drive failed. - The failed logical drive status displayed incorrectly during an array move, expansion or shrink. - ENHANCEMENTS - Added support for HP ProLiant G7 Servers. - Added support for Integrated Lights-Out 3 (iLO 3). - Included a document called HP_SNMP_Trap_Guide.txt that describes the Linux SNMP trap ID messages generated by the agent - Improvements to distribution identification including more consistent output and increased support for community and region al distributions. - Added support for Solid State Drives. - Added support for HP StorageWorks 2000sa Modular Storage Array and HP StorageWorks MSA2012sa/ MSA2312sa/ MSA2324sa when co nnected to HP SC08Ge Host Bus Adapter. - Added support and trap support (link up/down message) for the following HP NC-Series: . HP NC542m Dual Port Flex-10 10GbE BL-c Adapter . HP StorageWorks CN1000E Dual Port Converged Network Adapter . HP NC550m Dual Port Flex-10 10GbE BL-c Adapter . HP NC551m Dual Port FlexFabric 10Gb Converged Network Adapter . HP NC551i Dual Port FlexFabric 10Gb Network Adapter . HP NC362i Integrated Dual Port Gigabit Server Adapter . HP NC362i Integrated Dual Port BL-c Gigabit Server Adapter - FIXES - Modified the 6064 trap implementation to reflect the correct error. - Removed unnecessary information in cmahostd related to bonding driver, in order to improve performance. - Fixed an issue to display the Port number of Physical drives connected to Fiber Channel controller. - Fixed an issue to display Parity group count for RAID 50 and RAID 60 Logical drives. - Modified the script to get the NIC ports details from /sys/class/net. - Fixed an issue where wrong physical address is displayed on SMH, resolution was provided by checking for pcidevice informat ion instead of subsytem device information. - Fixed an issue where SNMP Alerts/IMA trap were not received by HP SIM. - Fixed an issue where junk characters and misalignment on the console during reboot by adding new line in stop section. - Fixed an issue where Linux SMH shows incorrect bay/port information by adding support for virtual port. - Fixed an issue where cmanicd is filling /var/log/messages via setroublesoot, resolved by modified selinux policy package (H Pcmanic.pp). - ENHANCEMENTS - Enhanced HP SNMP Agents to retain default permission and ownership of snmpd.conf file. - Added support and trap support (link up/down message) for the following HP NC-Series: . HP NC551m Dual Port FlexFabric 10Gb Adapter . HP NC551i Dual Port FlexFabric 10Gb Adapter . HP NC365T 4-port Ethernet Server Adapter . HP NC543i 10Gb 2-port 4X Flex-10 QDR Server Adapter . HP NC553m 10Gb 2 port FlexFabric Converged Network Adapter . HP NC552m 10Gb 2 port FlexFabric Converged Network Adapter . HP NC553i 10Gb 2 port FlexFabric Converged Network Adapter . HP NC552SFP 2-port 10Gb Server Adapter . HP StorageWorks CN1000Q Dual Port Converged Network Adapter . HP NC525m 10Gb 2 port FlexFabric Converged Network Adapter - FIXES - Fixed an issue where unwanted messages getting logged in the cma.log was resolved by removing the fprintf for virtual port. - Fixed an issue where cmanicd leaves trail of zombie lspci processes by modifying lspci usage in port_map.c and redirected o utput to /dev/null. - Fixed issue not to display driver messages on console for HP B110i Smart Array controller. - Fixed issue on CmaX, which displayed parsing error message on the syslog during agents reboot - ENHANCEMENTS - Added support for the MIBs in the Power Supply Table. - Added support for the MIB that specifies the version of Insight Management Agents running on the system. - Added support for the HP NC552m 10Gb 2-port FlexFabric Converged Network adapter. - FIXES - Addressed the tape drive not being displayed on the SMH on few configurations. - Displayed the placement correctly for the failed drive after reboot. - On Cmax, net-snmp displayed duplicate registration message on the syslog. - Modifications are done in code to support the HP NC542m for which PCIID information is the same for both the ports. - ENHANCEMENTS - Initial release to support Red Hat Enterprise Linux 5 Update 6. - ENHANCEMENTS - Added support to display "N/A" for non reactive thermal sensors instead of "0" value. - Added support to expose firmware version details for FMP, FPGA and cPLD (XNC) firmware. - Added support to report USB key/SD card information. - Provided greater than 2TB physical disk support for smart array and dumb SATA chipsets. - Added new accelerator error code: "Flash Backed Cache Erasing Flash Memory". - Added Physical Disk Temperature support. - ENHANCEMENTS - Added support for HP ProLiant Gen9 Servers. - FIXES - cmafcad daemon appears to cause segmentation fault. - cmastdeqd daemon appears to cause segmentation fault when removing USB key. - ENHANCEMENTS - FIXES - FIXES - Cmahostd does not ignore nfs4 mount points. - cmahostd triggers NFS auto-mounting and resulted in performance problem. - Files in directories under /var/spool/compaq/hpasm/registry/ have SGID bit set removed. - Initial development - Added support the HPE StoreFabric 84E 4-port Fibre Channel Host Bus Adapter - Added support for HPE StoreFabric SN1200E 1P & 2P, HPE StoreFabric SN1600E 1P & 2P - Added support for HPE Synergy 3530C - Added Obsoletes tag since the rpm has been changed from noarch to x86_64 bit - Initial development - Added support for SN1600Q 1P & 2P devices - Added support for 84Q and 3830C devices - Added Obsoletes tag since the rpm has been changed from noarch to x86_64 bit - Extension of -w option to include more iLO configuration - Fixed an issue where previous version of hponcfg failed to support older iLO Channel Interface drivers - Support for iLO3, iLO3 identification - Fixed an issue related to dynamic linking of hponcfg with libcpqci.so to resolve rdp related issue. - Support for Gromit XL devices has been added - Fixed an issue related to reset command for iLO3. - "Featrure not supported error" has been fixed for iLO3. - Added supoort for integrated Lights-out 4(iLO 4). - Bug fix release for v4.0.0-0 - Added support for iLO4 1.20 FW - Added IPv6 support - v4.2.0 is mainly targeted for iLO4 1.30, iLO3 1.60 and iLO2 2.20 - Created 32 bit and 64 bit RPM Packages to load shared library from hp-helth agent as libcpqci.so (in case of 32bit OS) and libcpqci64.so (in case of 64bit OS) - v4.3.0 is mainly targeted for iLO 4 1.40 and iLO 3 1.70 - v4.4.0 is mainly targeted for iLO 4 2.00 and iLO 3 1.80 - v4.5.0 is mainly targeted for iLO 4 2.20 and iLO 3 1.80 - v4.6.0 is mainly targeted for iLO 4 2.20 and iLO 3 1.80 - v5.0.0 is mainly targeted for iLO 5 1.10 - v5.1.0 is mainly targeted for iLO 5 1.15 - v5.2.0 is mainly targeted for iLO 5 1.20 - v5.3.0 is mainly targeted for iLO 5 1.30 - Changes include to select correct libssl.so file when multiple Openssl installed (32-bit and 64-bit) - Changes to remove the low level openSSL calls. - Improved trust mode during upgrade - Fixed group configuration management during Replicate Agents Settings (Severity: Serious) - Improved SMH service management - Fixed PHP files to avoid crash (Severity: Serious) - Improved webapp configuration files - Fixed SMH supporting DLLs to avoid version conflicts (Severity: Serious) - updated properties of SMH setup file - Updated secured handling of HTTP response - Updated Libxml2 to version 2.7.8 - Updated PHP to version 5.3.10 - Updated Curl library to version 7.24.0 - Updated OpenSSL to version 1.0.0h - Updated SMH service runs with managed privileges - Enable support of Windows 2008 R2 Sp1 - Server Core - Enable support of Windows Server 8 (Beta) - Enable support of Windows Multipoint Server 2011 for x64 - Enable support of Microsoft Windows Small Business Server 2011 for x64, Standard and Essentials - Updated usability of IP restrictions with SMH Command Line Interface - Updated information provided on webapp availability & loading statistics - Added support for Firefox 9.0 & 10.0 * Thu Oct 13 2011 Hewlett-Packard Development Company, L.P. 7.0.0 - Fixed SMH improperly displayed an invalid certificate warning when restarted, even on a fresh install. (Severity: Medium) - Added a command line option to modify the local and state information in the SMH PKCS (Public-Key Cryptography Standards) data - Added secured handling of HTTP request and response - Added support for Firefox 6.0, 7.0, 8.0 and Internet Explorer 9.0 - clarified the log messages - Improved handling of command Line Interface options - Improved handling of IP fields - Improved handling of memory resources - Improved handling of revoked trusted certificate - Improved handling of SMH configuration file and settings - Improved CLI options, for easier management of SMH configurations - Updated the HTTP links - Updated Apache to version 2.2.21 - Updated Curl library to version 7.21.7 - Updated OpenSSL to version 1.0.0e - Updated PHP to version 5.3.8 - On some Non-English Windows Operating Systems, user is not able to login into SMH 7.1.0. This version will solve this problem (Severity: Critical) - Improved security features of PHP (Severity: Critical) - Improved security features - Improved logging on few Operating Systems - Enable support of Red Hat Client 5.8 - Updated OpenSSL to version 1.0.1c (Severity: Critical) - Updated PHP to version 5.3.14 (Severity: Critical) - Improvement in RPM packaging - Updated Apache to version 2.4.3 (Severity: Critical) - Improved logging on few Operating Systems - Improvement in Certificate management - Added support for Firefox ESR 17.0 and Internet Explorer 10.0 - Enable support for Transport Layer Security (TLS) protocol 1.1 / 1.2 - Improved User Interface for Online Help - Improved CLI options for easier management of SMH configurations - Secured handling of HTTP communication - Updated the following components PHP to version 5.4.11 Curl to version 7.28.1 - Enable support of SUSE Linux Enterprise Server 11 SP3 - Enabled Simplified Chinese localization - Updated the following components Apache to version 2.4.6 Libxml2 to version 2.9.1 OpenSSL to version 1.0.1e Curl to version 7.32.0 PHP to version 5.5.2 - Packaged zlib 1.2.8 with SMH - Enabled support of 2048 & 4096 bit certificate for Single Sign-On (SSO) - Enabled FQDN (Fully Qualified Domain Name) for the CN (Common Name) field in the self-signed certificate & CSR (Certificate Signing Request) - Enabled support for Red Hat Enterprise Linux 7 - Updated the following components PHP to version php-5.5.13 Curl to version curl-7.35.0 Openssl to version openssl-1.0.1h - Improved SMH to use the system resources efficiently - SMH Plugin integration is modified - Enabled Japanese localization in SMH smart component installer - Removed files related to Namazu - Removed the checks for ZLIB installation - Updated the following components PHP to version php-5.5.18 Curl to version curl-7.38.0 Openssl to version openssl-1.0.1j - Disabled SSLv3 Protocol - SMH is been improvised with respect to security vulnerabilites - Updated the following components Apache to version httpd-2.4.10 - Updated the following components PHP to version php-5.5.23 Openssl to version openssl-1.0.1m - SMH is been improvised with respect to security vulnerabilites - Updated the following components PHP to version php-5.6.11 Openssl to version openssl-1.0.2d Curl to version curl-7.42.1 - SMH is been improvised with respect to security vulnerabilites - Updated the following components PHP to version php-5.5.28 - HP SMH self-signed certificate signature is changed to SHA-2 - SMH is been improvised with respect to security vulnerabilites - HPE Rebranding changes - Updated the following components PHP to version php-5.5.31 cURL to version curl-7.47.0 OpenSSL to version openssl-1.0.2g Libxml2 to version libxml2-2.9.3 - SSL protocol is now configurable through smhconfig cli - SMH is been improvised with respect to security vulnerabilites - Updated the following components PHP to version php-5.5.38 cURL to version curl-7.49.1 OpenSSL to version openssl-1.0.2h Libxml2 to version libxml2-2.9.4 - SSL Cipher Suite is set to TLSv1.2 as default - SMH is been improvised with respect to security vulnerabilites Upgrade Requirement: Recommended – HPE recommends users update to this version at their earliest convenience. - Updated the following components PHP to version php-5.6.27 OpenSSL to version openssl-1.0.2k Apache to version httpd-2.4.25 - SMH is been improvised with respect to security vulnerabilities Upgrade Requirement: Recommended – HPE recommends users update to this version at their earliest convenience. - Updated the following components PHP to version php-5.6.30 OpenSSL to version openssl-1.0.2k Apache to version httpd-2.4.25 - SMH is been improvised with respect to security vulnerabilities Upgrade Requirement: Recommended – HPE recommends users update to this version at their earliest convenience. - Supported the SLES 15 OS Upgrade Requirement: Recommended – HPE recommends users update to this version at their earliest convenience. - Please refer to online documentation by searching for the "Smart Storage Administrator Configuration Utility" using the search box on http://www.hpe.com. Then select the Download software link, select your operation system. Under the Enhancements tab is a description of the changes. (Severity: Low) - Please refer to online documentation by searching for the "Smart Storage Administrator Configuration Utility CLI" using the search box on http://www.hpe.com. Then select the Download software link, select your operation system. Under the Enhancements tab is a description of the changes. (Severity: Low) - Please refer to online documentation by searching for the "Smart Storage Administrator Diagnostic Utility" using the search box on http://www.hpe.com. Then select the Download software link, select your operation system. Under the Enhancements tab is a description of the changes. (Severity: Low)